0
What else can I help you with?
What happens to a 200 watt speaker with a amp that pushes 240 watts?
If the speaker is rated at 200 watts and the amp pushes 240 watts, there is a risk of overpowering and damaging the speaker. Exceeding the speaker's power handling capacity can cause distortion, overheating, and potentially result in permanent damage. It is important to match the power ratings of the speaker and amplifier to avoid such issues.
How many watts is a alpine v12 mrv-t501 amp?
The Alpine V12 MRV-T501 amp has a maximum power output of 500 watts.
Can 100 watts amp handle 300 watts subwoofer i have a pioneer 300watts sub and a 100 watts rockford amp will the amp handle it or it will get fry?
An amp can only put out so much power without distortion. A speaker, say, a subwoofer, will utilize whatever the amp is able to put out. So the question is not will a speaker fry an amp, but whether the amp will blow the speaker. (Not, in your example) Any speaker, though, needs a certain amount of power to begin to drive it to listenable levels. High-efficiency speakers like bass-reflex speakers need only 5 or 10 watts for loud levels, while a low-efficiency speaker may not even make a squeek until they are fed with 10 to 15 watts of power. sO will this set up work or not?
How many watts does a stereo have to have to run a 1500 watt amp?
My personal rule of thumb is that the amp should be at least 40% more powerful than the speaker(s) it's driving. So, if your sub is 1500W RMS, then mathematically, you'd need approximately a 2100W RMS amp. Some people just match it evenly - in that case you'd need a 1500W RMS amp. Whatever you do, DON'T use an amp less powerful than the speaker. If you do, you will probably kill the speaker in a short period of time. :(
5 amp and 100 volts is what wattage?
The wattage would be 500 watts. This is calculated by multiplying the amperage (5 amps) by the voltage (100 volts), resulting in 500 watts of power.
Can you use a 300 watts amp on a 700 watts 6.9 speakers?
im by no means an expert but the answer is yes you just wont get full potential out of the speakers. the amp is pushing 700 watts the speakers are capable of catching 1000 watts.
Does a 400 watt 2 channel amp have 2 channels of 400 watts each or 2 channels of 200 watts each?
500 and 27 watts
How do you match speaker with amp?
To match a speaker with an amplifier, ensure that the amplifier's power output (measured in watts) is compatible with the speaker's power handling capacity. Ideally, the amplifier should provide power within the speaker's recommended range, typically around 50-75% of the speaker's maximum rating for optimal performance. Additionally, match the speaker's impedance (measured in ohms) to the amplifier's output impedance to avoid damaging either component. Finally, consider the amplifier's tonal characteristics and intended use to ensure they complement each other.
How many watts are needed to push a kicker 12?
It depends on the model speaker. The speaker has an RMS amperage rating used for choosing the amp size needed. You would want to choose the upper number if there is a range. For example 50-200 rms watts, choose an amp with 200 watts. It is worse for the speaker to have too little than too many amps. Crutchfield even recommends 75%-150% of the RMS rating. You will also need to know the OHMs of the speaker when choosing the amp. There are sub woofers rating at 2 and other rated for 4 OHMS and have different amp requirements.
Can you use a 52 watt stereo with 1000 watt speakers?
sure you can, your amp will only deliver 52 watts to the speaker, more importend would be the impedance of the speaker . it should be equal to what your amp has! may be 8 ohms
How big an amp should I use to power 500 watt speaker PA monitor?
1000W will be suitable. See the specifications of speaker.
What will a 3000 watt amp do to a 300 watt speaker?
Using a 3000 watt amp with a 300 watt speaker can potentially damage the speaker due to overpowering it. The excessive power can cause the speaker to blow out or distort the sound quality. It's important to match the power ratings of the amp and speaker to prevent damage.
