0
What else can I help you with?
How do you adjust the flywheel on a 2004 Dodge?
There is not an adjustment on a flywheel. Your problem will most likely be the starter.
When I try to turn my bike on it wont turn over. All that you hear is the starter spinning. Is it the Starter Clutch that needs to be replaced?
It can be the starter bendix is not engaging the starter gear into the flywheel. It can also be a broken tooth on the flywheel itself. Try pushing the bike and then releasing the clutch. This will turn the engine over just enough to move the flywheel. If it then engages and starts, suspect you have a broken tooth. If that is not the case, then remove the starter and test it by applying 12 volts and see it the bendix kicks the gear out.
What causes problems with the fly wheel and starter to reoccur on my 1988 Chevy pickup 1500 since both have been replaced?
is the problem,that the flywheel teeth are being chewed out and same on starter. or is the problem that starter and flywheel do not mesh properly when engaged? if either of thses is the problem,this means that the gear on the starter is not matched to the teeth on the flywheel. other problem that could be causing this is none or incorrect shims used when installing starter motor. to fix this, you need to make a mark on the flywheel(use white out or something like that),and count the number of teeth.then do same on the starter motor.then find out from a drive line specialist,how many teeth shoud be on starter motor to match the flywheel.they can also tell you the shims to be used when installing starter motor to get proper clearance.
Have 351 windsor two of them a 1986 and 1990 both with same problem when the starter engages it slips on the fly wheel replaced starter and fly wheel and it still does it never had this problem onford?
I'm not sure what you mean by "slips". Is the starter making a grinding noise or does the starter sound like it is missing the flywheel completely? My first thought was a bad starter drive (part of the starter) but if you replaced the starter with a new one it shouldn't be that.
What could it be Loud grinding clunky noise when starting?
Defective starter, or a problem with the flywheel. You need to check the starter and then remove it and check the flywheel.
Will repeated failed attempts to start a car result in a flywheel problem?
Not unless there was a problem with the drive gear on the starter that makes contact with the flywheel.
What causes a bad fly wheel on an automatic transmission car?
The flywheel can be cracked or the teeth on the flywheel can be broken or worn. Either of these conditions require the flywheel be replaced. I would also replace the starter when replacing the flywheel. This will prevent damage to the new flywheel from the worn teeth on the old starter.
Will a high torque starter work on a flat spotted flywheel Cause the regular starters just hit the flywheel.?
The answer to the question is no. If the flywheel is ground or damaged it needs to be replaced.
I replaced starter 6 times in 6 month period and have replaced the flywheel I am still going through starters I have a 1971 350 camaroNoone can figure out why this is happening Can you help?
If you have headers put a heat shield over the starter. That is what fixed my 84 C-10 starter issues. If it is a gear alignment problem try shimming. If it is a electrical problem try the heat shield.
Have you had problems with Ford Mondeo diesel flywheels?
Yes. I've a 2004 mondeo tdci and the dual mass flywheel went at 110,000 miles. It began with starter problems -sometimes working, sometimes not engaging. There was a build up of dust on the starter cog from the disintigrating flywheel. It cost about £650 to replace (including clutch) have had the same problem and had to replace the flywheel and clutch.. after 65000 miles..mechanic was not impressed with the mondeo flywheel and replaced it with a passat part
Is the flywheel on a 5.7 liter Chevy pickup a problem starter or flywheel makes high pitched spinning sound.?
Could be either a defective starter drive or a broken tooth on flywheel Try turn the engine manually (large socket on crankshaft) to see if it will start- if so problem is a broken tooth - if not problem is probably a bad starter drive. (make sure vehicle is in neutral if std.)
Starter spins but does not engage the flywheel?
The Bendix on the starter motor is not working properly, most likely. A fix entails the dismantling of the starter motor assembly and the work of a knowledgeable person to rebuild it. It's usually easier and cheaper to just get a rebuilt starter. The problem was not your starter! Sick of hearing that answer, but sadly I do not have the correct answer. My car was having the same issue, mainly on cold starts. I took the poor advice and replaced the stater and solenoid, that evening...Same problem! You will only need to replace your started if the real problem is not found, because it will grind off the teeth in the starter and may even destroy your flywheel! I am not a mechanic but after owning a 98 Dodge Intrepid I feel I know more than most! Again, do not replace the starter until you find the real problem or you will go thru starters like candy! BUT dont take to much time or you will be replacing the flywheel too!
