0
What else can I help you with?
Is 4000 watt amp too much for two twelves subs?
Not if subs are rated for 2000 watts each.
What is the best way to wire 2 svc 2 ohm subs with a Rockford Fosgate T500 1db?
How much power can the subs take in terms of RMS wattage? You can either wire them to a 4 ohm load where they will each see 125 watts, or to a 1 ohm load where they each get 250 watts. Rockford Fosgate supplies a very useful feature for showing how to wire the subs for the impedance that you want: http://www.rockfordfosgate.com/rftech/woofer_wizard.asp
How many watts do you need to power three 600 watt subs?
To power three 600-watt subwoofers, you would need a minimum of 1,800 watts, as each sub requires 600 watts. However, it's advisable to have a little extra headroom in your amplifier to ensure optimal performance and avoid distortion. A power supply of around 2,200 to 2,500 watts would be ideal to accommodate any peaks and ensure the system operates efficiently.
What is good for some hypnotic subs that are 600 watts rms?
Hypnotic doesnt make good subs.
Can you run 2 subs with a 800 watt amp?
yes you can if each subwoofer is 400 watts (or very close) you can hook up multiple subs if it has more than one out put. hope this helps
Will a 1000 watt amp power two fosgate p3 12inch subs?
In a sense it would, say that 1000 watt amp was a mono channel. that would mean its 1000 watts RMS @ 1-0hm, 2 RF p3 4ohm would make it 500 watts to the two. if you want full power you need a 1200 watt amp @ 1-ohm, that would make it 600 watts to the 2 and that is the RMS of those subs. you can run more but running above RMS can blow or distort the subs.
If you have two 400 watts rms subs 1200 max kenwood kfc-w3011 what power amp should you get?
1000W Kenwood KAC-7204 2/1
Can you hurt a receiver if you hook up 2 subwoofer amps to it via a Y connector. Receiver is rated at 135 watts per channel subs at 100 watts each?
Yes, you can y cord the inputs of amps but not the outputs.
How much watts should you get in a amp for two 700 watt subs?
To properly power two 700-watt subwoofers, you should aim for an amplifier that can deliver at least 1400 watts RMS (root mean square) total, assuming the subs are wired in parallel. This allows for sufficient power for both subs to perform optimally without distortion. It's also advisable to choose an amp with a bit more wattage than needed to ensure headroom, so a 1600 to 2000-watt amp would be ideal. Always check the specific impedance ratings of your subs and amp for compatibility.
How big should the amp be to two 12 subwoofers?
What you need to know is the RMS power rating and ohms of the subwoofer. (Example; RMS is 300 watts and it is a 2 ohm sub. This is what you would need. You have 2 subs so a total of 600 watts. So you want an amp with a max power rating of 600 watts, but he is the tricky part. They were 2 ohm subs. So your amp needs to be 2 ohm stable. No there all not 90% of amps are only 4 ohm stable.)
If you put more amps to your sub will it hit harder?
yes say you have a 10" kicker sub that needs 250 watts to hit and you have a 1000 watt kicker amp you have to much power going into that sub so it will hit harder. BUT if you but more subs and your amp has a few channels you can send the right amount of power to the subs without risking damage. i have 2 12"kickers with a 1000 watt amp so i have to much power but my subs sound amazing so do what you want most subs are $80-180 HAVE FUN
Can a Jensen powerplus 1302 power two 1300 watt subs?
it will them. You will have to hook them in 2 ohm. (bridged and parrallel) This will dump about 500 peak to each sub. It will sound good, but it wont be the maximum power rating for the subs
