answersLogoWhite

0

In general, you can't stud ANY used tire. The manufacturers provide small holes for tire studs and once a tire is driven even a few miles, those holes fill up with grit and road debris. It will be almost impossible to find a tire store that's willing to stud a used tire, since the process will involve digging out whatever has built up inside those stud holes.

I also wouldn't trust the studs to stay in the tire if someone DID dig out the debris.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How can a flat tire be removed from a BMW if the dealer does not have the key to unlock the tire?

the locking nut needs to be cut off with a blow torch and a new nut used when wheel is replaced someone that knows what he is doing , needs to do this , so as not to mess up wheel stud, or you will have to replace stud as well


How do you fix a broken stud on a left front tire on a 97 Geo Tracker?

You must have to get a new or used (acceptable condition)rotor or hub if separated.


How do you take off a stripped tire stud on a 1997 subburban?

the stud is pressed into the hub using an impact hammer or a large ball pein hammer strike the stud until it pops out the inside of the hub


How much to replace a broken lug nut stud?

In Mr. Tire, $65.00 up.


What is a stud off a collective noun?

The noun 'stud' is used as a collective noun for a stud of horses, a stud of mares, or a stud of poker players.


How do you stud winter tires?

its against the law to have studded tires EDIT: NOT TRUE. Studded tires are not illegal everywhere. Certain states and provinces allow studded tires between set dates during the season. Check with your local laws. To stud a tire, it needs to be a special tire that was made to accept studs.


What do you do with a stud horse?

A stud is used for breeding and halter show only.


Did Nicki Minja used to be a stud?

No Nicki Minaj did not use to be a stud.


How do you change a rear wheel stud on a au?

On most vehicles you take off the tire, put the lug nut back on the stud and drive it out with a hammer . When you put the new stud in you can line it up and drive it in with a hammer or pull it through with a few washers and the new nut.


How to replace wheel stud on a Mitsubishi 3000 gt?

I had a broken stud on the rear drivers side hub and all I did was I took the tire off, took the rotor/drum off, tapped the broken stud out and used a little brute force and ignorance to get the new one in. Then I took a lug nut, tightened it just enough to get it seated in it's hole, took the nut off, put the tire on, and torqued it to spec. Try it out, it might work for you to without having to disassemble the entire rear wheel assembly.


How do you replace a wheel stud on a Chrysler lebaron?

This is not a difficult task...raise vehicle off ground, remove the tire on the broken stud wheel, remove the brake pads remove the disc brake rotor, hit the broken stud with a hammer and thick flat punch driving it out of its bore. Be sure the back side to where the old stud is being forced out is clear of the stud while removing. To replace, fit new stud into the empty bore, place wheel lug nut on new stud backwards(flange facing you), with a good air compressor and a 1/2 inch impact gun run the stud nut down until the new stud is pulled all the way through the bore and is seated flush on the rear of the axle flange. re install the rotor, brakes, tire/wheel, etc. Carefully retorque the wheel lugs onto the the tire without stripping the threads. Tighten carefully with your 1/2 Impact Driver, donot over tighten and lube each wheel stud with W D 40 or the like.Happy Driving!!!


What type of drillbit used to drill broken manifold stud?

The type of drill bit used to remove a broken manifold stud is an extractor or easy out. A hole is drilled into the stud and then the extractor is used to dig in and unscrew the bolt.