0
First if you are talking about normal speaker (not subwoofer), I would not recomend doing that.
There is different ways to connect multiple speaker to one amplifier chanel.
You could wire it in serie or in parralel.
If your are talking about dual voice coil or more than 2 speaker, there is even more possibility to wire two or more speaker to one channel.
Now if you are talking about single voice coil subs, in a perfect situation, by wiring them in parralel, the wattage should not get lower but the impedence will be divided by the number of sub you hook up. You will need to make sure the amp can support a lower impedance.
What else can I help you with?
How many watts can the Rockford Fosgate Prime 2-Channel Car Amplifier handle?
The Rockford Fosgate R150-2 2-channel amp puts out 50 watts RMS per channel to your speaker system, or you can bridge it to supply 150 watts RMS to a subwoofer.
Can you attach additional speakers to the Bose 123 system?
In short, yes. you can add speakers to nearly ANY setup. however, you should be sure to add enough speakers with particular resistance (load/ohms) ratings in order to wire them in parallel and series so each channel has the same total ohms as the original speaker. If the total load on each channel is too high or too low, you could risk overheating the power source (head unit/amplifier), some headunits or amplifiers have built in safety mechanisms which turn off the unit if the load is either too high or too low. Keep in mind, when adding speakers, the power from each channel is split between them. For example, each speaker may get 100 watts, but if you add a speaker to each channel, each speaker will only get 50 watts. Not only this, but keep in mind Bose made some very specific connectors so you will have a hard time to add and connect the extra wires. The system is in no way made for this.
Your speakers will handle 400 watts but start to disort at 200 watts?
The speaker impedance does not match the amplifier's specified speaker impedance.
Which is better a 12.5 watts speaker or a 2 watts speaker?
It depends on the environment, a 2 watt speaker is usually smaller and more portable but a 12.5 watt speaker is louder and usually has better sound quality.
When a pair of 6x9s speakers are rated at 200 watts rms is that into one speaker or both?
Each speaker is rated at 200 watts rms
Is the sound louder the larger the watts speaker rating?
In laymen 's terms, yes. But the "Watts" of a speaker is not what the total power of the speaker is. The are usually two different ratings for speakers to determine the total power. One is "RMS", which means root-means square. And the terms "peak or continuose power". A speaker can be 400 Watts, 360 RMS, 390 continuous power. That means it will take an amp at least 400 Watts to drive the speaker properly. And the speaker will perform at 360 Watts RMS, and peak out at 380 Watts continuous power. Remember, u can't blow a speaker from overpowering it. Only from under power. The speaker will distort and sound horrible from overpowering, but it will not blow.
Is it safe to connect a 300W ampilifer to a 60W Speaker?
Without getting into the multitude of variables and keeping this as simple as possible, NO ...Simply connecting a 300 watt amp to a speaker (driver or cabinet) will do no harm, that is, until you make an attempt at raising the volume! A speaker rated at 60 watts means just that ...it can handle 60 watts. At low volumes, no harm will come to the speaker, driven more powerfully, harm may soon come to it.
Yes you can bridge this amplifier to a 2 channel at 4 ohm per channel for 200 watts out of each channel.?
Yes you can bridge this amplifier to a 2 channel at 4 ohm per channel for 200 watts out of each channel.
How many watts is the Bose speaker 401?
120watt
What speaker match a 1600 watt rms 2 channel amplifier?
To match a 1600 watt RMS 2-channel amplifier, you should look for speakers that can handle a power rating of at least 800 watts RMS per channel, assuming a standard setup where each channel drives one speaker. It's also important to consider the speaker's impedance; typically, 4-ohm speakers are a good match for higher power amplifiers, as they can draw more power. Additionally, ensure the speaker's sensitivity rating is suitable for your listening environment to achieve optimal performance.
What happens to a 200 watt speaker with a amp that pushes 240 watts?
If the speaker is rated at 200 watts and the amp pushes 240 watts, there is a risk of overpowering and damaging the speaker. Exceeding the speaker's power handling capacity can cause distortion, overheating, and potentially result in permanent damage. It is important to match the power ratings of the speaker and amplifier to avoid such issues.
How many watts in TDA85600?
The TDA85600 is a class-D amplifier chip that can deliver up to 50 watts per channel into a 4-ohm load or 30 watts per channel into an 8-ohm load.
