0
While it's not strictly necessary to use a torque wrench to change the tensioner assembly, it is highly recommended. Using a torque wrench ensures that you tighten the bolts to the manufacturer's specified torque, which helps prevent damage to the components and ensures proper function. Not using the correct torque can lead to issues like bolt loosening or overtightening, which may affect the timing system's performance.
What else can I help you with?
How do you replace a serpentine belt on a 2003 Toyota sequioa?
make sure you have a diagram, use a long box end wrench to torque the tensioner which is near the top. When you rotate the bolt head, it will relax the tensioner. Remove the belt and then replace around all components except the tensioner. Push on the tensioner wrench again to make room for the belt to go over tensioner.
How do you change thermostat on1988 Chevy truck. Serpentine Tensioner is in the way?
Must loosen the nut that goes through the tensioner. Pop the belt off, and put a wrench on the outside nut of the tensioner, so it will catch something when you torque the inside nut. You should be able to loosen the tensioner enough to get the strap wiggling enough to pop it off the thermostat housing stud.
If you add an exton to your torque wrench does it change the torque?
as long as your extension is 90 degrees from the handle it will not affect your torque wrench. if you use a super long torque wrench you may lose a little torque in the extension it self but should not affect torque. an extension affecting the wrench in lenght like a crows foot will affect torque as long as your extension is 90 degrees from the handle it will not affect your torque wrench. if you use a super long torque wrench you may lose a little torque in the extension it self but should not affect torque. an extension affecting the wrench in lenght like a crows foot will affect torque
How do you change belt tensioner pulley 1997 aerostar ford van?
To change the belt tensioner pulley on a 1997 Ford Aerostar van, first, disconnect the negative battery terminal for safety. Then, locate the serpentine belt and use a wrench to relieve tension on the tensioner pulley, allowing you to remove the belt. Next, unbolt the old tensioner pulley from the tensioner assembly and replace it with the new pulley. Finally, reattach the serpentine belt and reconnect the battery terminal.
How do you change the tension pulley on a 1993 Chrysler New Yorker?
To change the tension pulley on a 1993 Chrysler New Yorker, first, ensure the engine is off and cool. Locate the tensioner assembly, then use a wrench to rotate the tensioner arm counterclockwise to relieve tension on the serpentine belt. Remove the belt from the tension pulley, then unbolt the pulley from the tensioner assembly and replace it with the new pulley. Finally, reattach the belt, ensuring it's properly routed, and reapply tension to the belt by releasing the tensioner arm.
How do you change alternator axiom 2002?
Disconnect battery ground cable.Move drive belt tensioner to loose side using wrench then remove drive belt (1).Disconnect the wire from terminal "B" and disconnect the connector (4).Remove generator fixing bolt (3).Remove generator assembly (2).InstallationInstall generator assembly to the position.Install generator assembly and tighten the fixing bolts to the specified torque. Torque: M 10 bolt: 41 N.m (30 lb ft) M 8 bolt: 21 N.m (15 lb ft)Connect wiring harness connector and direct terminal "B".Move drive belt tensioner to loose side using wrench, then install drive belt to normal position.Reconnect battery ground cable.
Do you have to change your torque wrench setting if you use a extension?
No, it remains the same.
How do you change the belt for a 95 mark 8?
wit a 1/2 wrench, put it in the tensioner
How do you change a the serpentine belt on a 2002 Chevy Trailblazer?
Put a wrench on the tensioner. Push it slack. Replace the belt while holding the tensioner in the slack position.
Does loosening a bolt with a torque wrench hurt the torque wrench?
yes
Do you need a torque wrench when replacing pads and rotors?
You do not need a torque wrench when replacing brake pads and rotors. Some of the tools needed to change the rotors and pads are the c-clamp, sockets, wrench, grease, and brake cleaner.
What do you need to change front wheel hub assembly on a 2003 Pontiac Grand Am?
Getting ready to do the same thing myself--foound out you will need a 34MM deep socket, torque wrench but I am still trying to find torque spec for axle nut--GOOD LUCK
