0
You may want to check to see if this was covered by the Chevy recall for the tailgate problems on the 2000 Silverado. I don't remember - you can either look up the TECH Bull. or just call your local Chevy dealer and ask. When I inherited my dad's truck, I looked at the recall/service CHEVY page and took the truck in to have that work done for free. Worth the phone call...
What else can I help you with?
How do you change the tailgate strut on a peugeot 307sw?
To change the tailgate strut on a Peugeot 307 SW, first, ensure the tailgate is supported to prevent it from falling. Use a flathead screwdriver to gently pry off the retaining clips at both ends of the strut. Once the clips are removed, detach the old strut from the mounting brackets and replace it with the new strut, securing it with the clips. Finally, test the tailgate's operation to ensure the new strut is functioning correctly.
What do I do when the tailgate will not open on 2001 silverado?
Most often the cause is two broken clips inside the tail gate mechanism. By pushing upwards you can remove the plastic bezel around the tailgate handle; its just snapped into place. You should now be able to see the mechanism under the handle. There are two metal bars coming in from the sides of the tailgate. These operate the latches on either side of the tailgate. They are attached to the central tailgate handle mechanism by plastic clips. One is pink and one is green; colored to indicate whether they go on the right or the left. You can get these clips from a dealership for about 5 bucks a piece. Hope that helps.
How do you remove tailgate bezel in 2010 Chevy silverado?
To remove the tailgate bezel on a 2010 Chevy Silverado, first, lower the tailgate and locate the screws securing the bezel, typically found on the underside. Use a screwdriver to remove these screws. Once unscrewed, gently pry the bezel away from the tailgate, starting from one end and working your way to the other to avoid breaking any clips. Finally, disconnect any wiring harness if applicable, and the bezel should come off easily.
How do you remove tailgate bezel in 2006 Chevy Silverado?
2 clips on bottom of bezel have to be pushed up via a very slim device such as a putty knife,etc and then pulled out & down to get free of the top retainer hooks. Tape secures both sides of the bezel to the tailgate so a hard pull may be necessary. (9 out of 10 times the bottom bezel clips break during removal)
How do you remove the tailgate off a 2013 dodge ram 1500?
To remove the tailgate from a 2013 Dodge Ram 1500, start by ensuring the tailgate is in the fully open position. Locate the hinge pins on either side of the tailgate, and use a flathead screwdriver or a similar tool to gently pry out the retaining clips. Once the clips are removed, lift the tailgate upward off the hinges. Be cautious and have an assistant if necessary, as the tailgate can be heavy.
How do you replace tailgate on 1997 gmc sonoma?
To replace the tailgate on a 1997 GMC Sonoma, start by lowering the tailgate fully and removing the retaining clips or bolts from the hinges using a socket wrench. Once the hinge bolts are removed, lift the old tailgate off the hinges. Position the new tailgate onto the hinges, then secure it by reinstalling the bolts or clips. Finally, test the tailgate to ensure it opens and closes smoothly.
How do you change a tail light on a 1990 Chevy Silverado?
Remove the two screws holding the assembly from inside with tailgate down. Carefully pull and wiggle assembly outward until the two clips release, unplug harness, remove the two 1/4" bulb retainer screws to get at the bulbs. I hope this helps you. Mark
How do you change lock barrel 2002 fiesta van tailgate?
To change the lock barrel on a 2002 Fiesta van tailgate, first, open the tailgate and remove any plastic trim or covers that conceal the lock mechanism. Next, locate the retaining screws or clips holding the lock barrel in place and remove them. Once the old barrel is free, insert the new lock barrel into the mechanism and secure it with the screws or clips. Finally, reassemble any trim pieces and test the lock to ensure it functions properly.
How do you change the lock on fiesta mk 6 tailgate?
To change the lock on a Fiesta MK6 tailgate, first, ensure the tailgate is open and disconnect the battery to avoid electrical issues. Remove the interior trim panel by taking out any screws and clips, then access the lock mechanism. Disconnect the wiring harness and remove the lock assembly by unscrewing it from the tailgate. Install the new lock by reversing the process, ensuring everything is securely reattached before reassembling the trim.
Where is the blower motor resistor on a 2004 Chevrolet Silverado crew cab?
The blower motor resistor on a 2004 Chevrolet Silverado crew cab is typically located under the dashboard on the passenger side. It is mounted on or near the blower motor itself, usually accessible by removing the lower dash panel. You may need to remove a few screws or clips to gain access to it.
How do you change the tailgate wiring harness on a Volvo 240 wagon?
To change the tailgate wiring harness on a Volvo 240 wagon, first, disconnect the vehicle's battery to ensure safety. Remove the interior trim panel of the tailgate to access the wiring harness. Detach the old harness by unplugging the connectors and securing clips, then install the new harness by reversing the process, ensuring all connections are secure. Finally, reassemble the trim panel and reconnect the battery to test the tailgate functions.
Where can i get the hardware clips for tailgate to connect with soft top?
check a local junk yard or ebay.
