0
The thead on the pully bolt is reversed. Pulling on it with a spanner in the anticlockwise direction will lock up the thread and reduce tension on the pully arm but its spring loaded so you need a friend to help or one hand free to slip the belt off while your holding the pulley back.
What else can I help you with?
How do you replace the belt tensioner on a vs v6 commodore?
To replace the belt tensioner on a v6 commodore you start by removing the fan belt by using a 18mm spanner and rotating the pulley assembly anti clockwise. Undo the bolt by holding the tensioner pulley on and use the 18mm spanner to turn bolt clockwise to undo threaded. Place new pulley onto shaft, drop some Loctite onto bolt and screw in. Rotate pulley anti clockwise and put the fan belt back in.
How do you put a fanbelt on a VT commodore?
the vt commodore has a automatic tensioner. you will need a 15mm socket and breaker bar or spanner. it is a left hand thread so if you apply pressure counter clockwise you will move the tensioner and be able to slip the belt on. that is if your talking about the v6 engine.
How do you adjust belt tension on a 99 Malibu V6?
you dont,the tensioner tightens the belt up.if belt sqeals get new belt or tensioner! on 3.1v6,
Is it necessary to change the tensioner when replacing the serpentine belt on a Ford 3.8 V6?
no, unless the tensioner is bad, other than that just the belt.
How do you loosen the assembly belt on a 1995 Chevy Camaro 3.4L V6?
by loosening the belt tensioner
How do you install a serpentine belt on a 2003 Saturn vue v6?
first make a drawing of the routing of the belt then loosen tensioner remove the old belt install the new belt as per your drawing and release the tensioner after you have made sure the belt is tracking as it should on the pulleys nothing to it good luck
How do you remove the belt tensioner on a ford winstar v6?
To remove the belt tensioner on a Ford Windstar V6, first, relieve the tension on the serpentine belt by using a wrench or ratchet to rotate the tensioner pulley counterclockwise. Once the tension is released, slide the belt off the tensioner pulley. Next, unbolt the tensioner from its mounting bracket using the appropriate socket or wrench. Finally, remove the tensioner from the engine bay for replacement or inspection.
How do you replace the belt tension er on a 1989 Chevrolet celebrity?
To replace the timing belt tensioner on a 1987 to 1990 Chevrolet Celebrity V6: 1. Use a 3/8" breaker bar to release the belt tension, move the belt out of the way. 2. Remove the single bolt out of the center of the fixed end of the tensioner. The belt tensioner will now come off. 3. Install the replacement tensioner and put the belt back on.
How do you put on serpentine belt on Mazda v6 meida?
To install a serpentine belt on a Mazda V6, first, ensure the engine is off and cool. Locate the belt routing diagram, usually found on a sticker near the engine bay or in the owner’s manual. Release tension from the belt by using a wrench to turn the tensioner pulley clockwise, then slide the old belt off and the new belt on, following the routing path. Finally, release the tensioner, ensuring the belt is secure on all pulleys.
How do you change the drive belt on a 1999 Pontiac grand am se v6?
To change the drive belt on a 1999 Pontiac Grand Am SE V6, first, ensure the engine is off and cool. Locate the serpentine belt tensioner and use a wrench to relieve tension on the belt. Remove the old belt, noting the routing path, and install the new belt in the same configuration. Finally, release the tensioner to secure the new belt in place.
What belt tensioner tool is needed for 1999 Ford E-350 Van with V6?
you do not need a tool to tension pully belt if belt is loose, belt needs replacing tensioner works automatically
How do you Loosen belt tension on 3100 v6 grand am?
The GrandAm has an automatic belt tensioner built in. Loosening the belt manually would not be feasable without the removal of the belt tensioner at which point the belt would no longer fit.
