0
blessing7u@Yahoo.com
My name is miss Blessing John,i am single and 5.5ft. How are you,i hope your are find and in sound health. I went through your profile today and i took interest on it. I am interested in your profile,Kindly contact me. (blessing7u@yahoo.com) I will tell you more about myself and picture
Thanks
Blessing
What else can I help you with?
How do you remove the plate under the steering wheel to replace turn signal switch on a 1987 Chevy truck?
It requires a SPECIAL tool that you can push the plate down with and then remove the lock ring that's around the steering shaft. There is a spring under the plate, IT MUST BE PUSHED DOWN TO REMOVE LOCK RING.
How do you remove the final piece from the steering column to remove the key switch and tumbler in a 1991 Oldsmobile Cutlass Supreme?
What you have is called the lock plate for the steering wheel. Go to your favorite auto parts store and ask them for a lock plate hold down tool. It will be needed to depress the plate's spring, so the snap ring can be removed that is holding the lock plate onto the steering shaft.
How do you remove ignition cylinder from 1988 Chevy pickup?
Remove the steering wheel. (you will need a steering wheel puller) Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column. Turn the lock to Run. If necessary, remove the ignition key. If equipped, remove the buzzer switch assembly. Remove the lock retaining screw and remove the lock cylinder.
How do you remove the steering lock on a 1994 Ford Probe?
# Disable airbag system. # Remove steering column covers and lower instrument panel cover # Lower steering column # Disconnect the shift interlock cable from ignition lock housing # The lock assembly is clamped to the steering column by two shear-head bolts. Drill heads off each bolt and remove the bracket. # Remove the steering lock assembly from the steering column
How do you fix the steering on a craftsman mower?
Remove the mower deck. Remove the phillips head screw at the end of the shaft underneath the mower. The releases your shaft from the bootom of mower. Remove steering wheel and remove shaft. Replace parts as needed.
How do you remove a steering wheel from a 1994 Mitsubishi 3000 gt?
To remove the steering wheel start by disconnecting the negative battery terminal to prevent accidental airbag deployment. Then remove the screws on the backside of the steering wheel to remove the airbag. Disconnect the airbag wiring connectors. Remove the steering column shaft nut and remove the steering wheel with a puller. Do not yank, hammer, pry the steering wheel off as this could result in steering shaft damage.
How do you remove steering shaft on 1997 Chevy venture?
Not an answerable question. Missing need option and specific identification of what steering shaft. There are at least three.
How do you install the key cylinder on a 78 Chevy pickup?
assuming that you're talking about the ignition cylinder on the steering column: you remove the horn button from the steering wheel, remove the safety snap ring from the main steering shaft, then the nut (most likely a 13/16 socket). then you buy or rent a steering wheel puller, remove the steering wheel. after the wheel is removed, you'll need to pry the black plastic cover from the wheel lock ring, which is what locks the steering wheel when the key is in the off or lock position. you'll need to get another tool now, to hold the lock ring down against the spring about 1/4 inch, while you remove the small outside snap ring from the groove in the steering shaft (pry it out of the groove with a small flat screwdriver). once the snap ring is out and the lock ring is removed, remove three Phillips screws which hold the turn signal switch in place, and pull it out and down over the shaft (leave the wiring harness attached, and let it hang down while you change the lock cylinder). now turn the ignition switch to the run position, remove the screw that holds it in the column, and pull the switch (cylinder) out. reverse procedure to re-install new cylinder.
How do you remove the ignition lock cylinder on a 1973 Firebird?
pull steering wheel off, remove the steering lock disc, then remove the signal light switch assembly to gain access to the retaining screw that holds the lock cylinder in place,
How to remove ignition switch on 89 berretta?
the ignition switch is commonly caled the key lock clyinder If you have tilt steering then you need to take it to a dealership they will have a specail tool to remove the pivot pins in the steering column housing. this makes key lock cylinder replacement impossible for the home auto repair technician. if it is not tilt steering 1) remove negative battery cable 2) remove steering wheel: probably need steering wheel puller for this. 3) remove turn signal switch assembly 4) place lock cylinder in RUN position 5) remove turn signal switch housing screws 6) remove turn signal switch housing and steering shaft assembly : as complete unit: 7) lift the switch tab with a screwdriver then GENTLY pull on the buzzer switch wires and remove the buzzer switch 8) place the lock cylinder in the accessory position 9) remove retaing screws fro lock clyinder and remove the lock cylinder. 10) reverse to install. hope this helps wolverine
How do you remove ignition switch from steering column on 84 Pontiac fiero?
you have to remove the steering wheel then using a lock plate removal tool depress the lock plate and removed the clip that holds it in place then remove the lock plate then remove the screws from the turn signal switch and pull it up slightly then remove the screw that hold the lock cylinder in place then remove the lock assembly
1994 mercury villager shift lock solenoid?
The shift lock solenoid is located on top of the steering column. You will need to remove the steering column covers, lower dash trim, and the heater duct. Remove the steering column bolts and lower the steering column to access the shift lock solenoid.
