0
disconnect the negative battery cable, as your looking at the motor from the front, the driver's side will be on the right. remove the top cover of the engine,6 10 mm bolts. you will see 2 almost identical plugs one on top of the other, one will have a notation or same part code as your new one ,ck sensor is crank sensor and cam sensor is a diff number. if you follow the wire from the cam sensor it will lead to just under the upper black plastic timing cover which has 2 0r 3 ten mm bolts,once you remove those you can wiggle that cover off and see the cam sensor behind the timing belt. you should be able to remove the two ten mm bolts holding it in and replace the sensor, good luck.I am not as fortunate ,I had to replace the crank sensor which was more extensive as it is behind the lower timing cover and one bolt is behind the hydraulic belt tensionerpulley and had to be released and move out of the way successfully without removing the radiator or timing belt.
What else can I help you with?
Where is the camshaft position sensor on a 2006 Kia Sorento?
do you need to take off the timing belt to replace a camshaft position sensor on a 2006 kia sorento
How do you replace 2008 Kia Sorento camshaft position sensor?
To replace the camshaft position sensor on a 2008 Kia Sorento, begin by disconnecting the negative battery cable to ensure safety. Locate the sensor, which is typically found near the camshaft on the engine. Remove the electrical connector and the mounting bolt securing the sensor, then pull the old sensor out. Install the new sensor by reversing these steps, ensuring it's properly seated, and reconnect the battery.
How do you replace replace the camshaft position sensor?
In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.
How do you replace the camshaft position sensor on a 1997 Plymouth voyager 3 L?
how do you replace the camshaft position sensor on a 1997 plymouth voyager 3l
How install a camshaft position sensor on a 2006 Kia Sorento where is it located?
To install a camshaft position sensor on a 2006 Kia Sorento, first, locate the sensor, which is typically situated on the rear of the engine, near the camshaft. Disconnect the negative battery terminal, then unplug the electrical connector from the old sensor. Remove the mounting bolt(s) holding the sensor in place, replace it with the new sensor, and reattach the connector and battery terminal. Finally, ensure everything is secured and check for proper operation.
Where is the camshaft position sensor located on a 1999 Oldsmobile Intrigue and how do you replace it?
where is the camshaft position sensor located on a 1999 Oldsmobile intrigue
How to replace camshaft position sensor for vw jetta 1999?
how to remplace position of oxigen sensor
How do you replace a camshaft position sensor on a 2000 Nissan Xterra?
How do u replace the camshaft sensor for a 2000 Nissan xterra 3.3L and where is its locatoin
If you replaced the camshaft position sensor should you replace the crankshaft position?
I changed only the camshaft position sensor on my 2000 Kia Sportage. So I don't think so.
Where is the crankshaft position sensor on a 2004 Kia Sorento?
TOP OF ENGINE JUST TO PASSENGER SIDE OF CENTRE. THE CAMSHAFT LOCATION SENSOR IS ALSO AT THE SAME LOCATION.
Where is the camshaft position sensor on a 2005 Kia Sorento?
under upper timing belt cover, driver side 3.5 eng
How do you replace the camshaft position sensor on Nissan Altima?
The camshaft position sensor is located near the thermostat housing. You should replace the crankshaft position sensor as well. This one is much harder to locate....it is on the backside of the engine that is between the firewall and the engine block. Both use the same sensor.
