0
Open the lift gate. Pull off the plastic interior trim, 4 snaps, just give it a gentle tug and it will come off pretty easy. Next, you will see to back of the red brake light and you will see 4 tabs along the bottom. There are also 4 tabs along the top that you can't see but there are the same and in the same locations as the bottom tabs.
Trick is to use 2 people to remove the brake light retainer, one using a screw driver. Have one person push in two tabs and the other to push in the other two, simultaneously. The 3rd tab from the left requires a screw driver as you can't fit your finger in the hole. As you both push in the tabs, gently push the brake light retainer outward, the bottom will disengage and then you can carefully pull down on it from the outside and disengage the 4 top tabs. Then just untwist bulbs and I'd replace all four. Reinserting is pretty easy, just gently push back in place.
What else can I help you with?
How do you replace bulbs on high mount stop light on 2001 buick?
There are no bulbs, it is a panel of mini-lights. You access this from the trunk area.
How do you replace the dash cluster bulbs in a 91 Camaro?
They mount to the back of the dash cluster. The bulbs are exposed when the panel is removed.
What are the lights in between the brake lights and tail lights?
Do you mean the center high mount stop lights? See sources and related links below to lookup bulbs by vehicle make, model and year.
What is wrong with brake lights won't work on your 98 Lincoln Town Car but the high mount one is?
Check bulbs
How do you replace fog light bulbs on 2002 Corvette?
To install the new bulbs, raise the hood and raise the headlights. Unhook the battery for safety. Look down between the rear of the headlights and you will see the wires that attach to the fog lights. Put your hand down in that space and twist the bulb mount. You should then be able to pull the light out. If you have small to average hands and forearm, and good dexterity, you should be able to can replace the bulb with this method. Do not touch the glass of the new lights. Remove the wire connector from the old bulb and replace it with the new. Twist the new bulb mount into place. Reconnect battery.
Why do the brake lights on your 2002 Ford Focus stay on when the car is moving but if you put the car in park and press the pedal the brake lights go on and off as you press and release the pedal?
Replace the bulbs in the high-mount brake light. Most likely they're all burnt out. I had the same problem, and that fixed it. Cost: $15.00 for the bulbs. See sources and related links below for bulb information.
How much to replace Mazda 3 motor mounts?
I had it done at the dealer, it was $260 for front mount on passenger side.
How do you replace the Mazda 626 motor mounts?
Each motor mount is held in place by a retaining bolt. The retaining bolt goes through the middle of the motor mount. Remove the retaining bolt. Jack the engine up. Replace the motor mount.
How do you replace the brake high mount stop light bulb in a 1993 cadillac deville?
There are actually 3 bulbs (GE #1141). On my De Ville there is a small compartment on the rear dash directly in front (from inside the car) the high mount brake light. Simply open the compartment and pull back the trim exposing the 3 bulbs, replace any or all nonworking bulbs.
Where is the motor mount on a Mazda MPV?
how many motor mount has a mazda mpv 2000
Why does my high mount brake light come on but not my other brake lights?
If you have directional lights, tail lights, and hi - mount brake light that works but no lower brake lights, replace the multi-function switch on the steering column. Order from MONSTER Auto Parts online for about $90.00. Buy from dealer 300-400.00. Parts house 200-300. No need to replace the 4 way flasher even though they do not work. They will when you replace the MultiFunction switch. Good luck!
How do you replace rear motor mount in a 2002 mazda mpv?
To replace the rear motor mount on a 2002 Mazda MPV, first, ensure the vehicle is securely lifted and supported. Remove any components obstructing access to the mount, such as the air intake or engine cover. Then, unbolt the old motor mount from the engine and the chassis, using a jack to slightly lift the engine if necessary. Install the new mount by aligning it properly and tightening the bolts to the manufacturer's specifications. Finally, reassemble any removed components and lower the vehicle.
