answersLogoWhite

0

where is the airbag sending unit for when yoy hit somone in the front where is that module for the airbag in the front. "If you want to replace it, bad idea, that will be ALOT more costly. I had my original SRS module sent in for a reset. I just googled a company called www.myairbags.com and they reset mine for $55 and shipped it back to me free of charge, I hooked it up and it works like brand new! and I saved about $560.

*Disconnect battery if you are working with the Airbag Module, if its powered and it feels movement, It could trigger the Airbags to blow."

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you replace the airbag module on a 2000 Ford Expedition?

Where is the airbag module on the 2000. Ford expedition


Where is the airbag module 1997 Oldsmobile achieva the light will not go off.?

The 1997 Oldsmobile airbag module sensor can be found below the dashboard on the drivers side. The airbag module should be labeled as such.


Where is the crash sensor volkswagen jetta 1997?

The front crash sensor is located inside the airbag control module.


98 airbag module where?

where is airbag module 98tacoma


Can you reset the air bag module on a 2001 mustang if not what needs to be replaced?

You can only replace the driver's airbag. The rest you will need to reprogram or replace the control module and replace the damaged area.


Do you have to replace the airbag sensor once an airbag has been used?

Yes. Most airbag sensors are triggered by breaking them so they are single-use only.


How to fix Passenger Airbag Cutoff Sensor ML320?

Replace seat pad


where is the airbag sensor module location on mazda b3000 2000?

The airbag sensor module location on a 2000 Mazda B3000 truck is typically located in the center of the vehicle, under the dash, near the steering column. It is a small, box-shaped module that is connected to the vehicle's electrical system and is responsible for deploying the airbags in the event of a collision. The exact location may vary depending on the specific model and trim level of the vehicle. It is best to consult your vehicle owner's manual or a repair manual for the precise location of the airbag sensor module on your specific vehicle


How do you replace the air bag module on a 2009 Chevy Cobalt?

To replace the airbag module on a 2009 Chevy Cobalt, first disconnect the negative battery cable and wait at least 10 minutes to ensure the airbag system is deactivated. Remove the necessary trim and dashboard components to access the airbag module, then unplug the electrical connectors from the old module. Install the new airbag module by connecting the electrical harnesses, securing it in place, and reassembling the dashboard components. Finally, reconnect the battery and check for any diagnostic trouble codes using a scanner.


How do you replace a airbag sensor on a 2005 Buick lesabre?

To replace the airbag sensor on a 2005 Buick LeSabre, first ensure the vehicle is turned off and the battery is disconnected to prevent accidental deployment. Locate the airbag sensor, which is typically found under the front seats or near the steering column. Remove the sensor's electrical connector and unscrew it from its mounting bracket. Install the new sensor by reversing the removal process, reconnecting the electrical connector, and reconnecting the battery before testing the airbag system.


Where is the airbag control module for a 2002 Acura TL located?

The 2002 Acura airbag control module is located on the firewall in the engine compartment. The airbag control module will be on the drivers side of the firewall.


How do you replace 2000 Chevrolet Impala air bag module?

To replace the airbag module in a 2000 Chevrolet Impala, first disconnect the negative battery cable to ensure safety. Remove the dashboard and any components obstructing access to the airbag module, typically located under the steering column or dashboard. Disconnect the wiring harness from the module and remove the mounting screws to take out the old module. Install the new module in reverse order, reconnect the wiring harness, and reassemble the dashboard before reconnecting the battery. Always remember to have the airbag system checked with a diagnostic tool after replacement.