0
How do you run the power wire for an amplifier from the battery to the trunk for a 1999 Chevrolet lumina?
I took out the back seat so i could run it underneath it, and then the trim along the doors, under them as well. I ran the wires for the stereo down the left side of the car. The power wire i ran up the left side. There is a wire under there that i could plug it into. There was a wire there i plugged into. I wired my power wire into the wire labeled power. It can only handle 10 Amps, and there is a very large warning sayin that if you overpower it, it can cause damage to your electrical system. I've never been able to find anything on this, so not sure what its for exactly, but I've had it wired up for a year or so now an its been fine. Better make sure ya do it professionally or it could cause problems as well. Make sure you have a 10 Amp fuse between your amp and this connection.
Hope this helps!
What else can I help you with?
How do you install a amp in a 2015 impala?
To install an amplifier in a 2015 Chevrolet Impala, start by disconnecting the car's battery to prevent electrical shorts. Next, run power and ground wires from the battery to the amplifier location, ensuring to use a proper fuse on the power wire. Connect the amplifier to the vehicle's audio system using RCA cables for signal input, and wire the speakers to the amp outputs. Finally, secure the amplifier in place, reconnect the battery, and test the system for proper operation.
What if your 93 Chevrolet lumina has a power loss on take off?
i have the same problem with my 92 Lumina and i cant figure it out i have tried every thing
Can a 12 volt battery charger use to power a 12 volts amplifier?
The battery charger can be used but it is not recommended. The battery charger does not have filtering on the its output like a power supply does. You will probably hear an AC ripple on the amplifier which will become very annoying when listening to the amplifier.
How do you replace power steering hose on 93 lumina?
To replace the power steering hose on a 1993 Chevrolet Lumina, first, ensure the engine is off and the vehicle is safely lifted. Start by disconnecting the negative battery cable and draining the power steering fluid. Remove the old hose by loosening the clamps and disconnecting it from the power steering pump and the steering gear. Install the new hose by securing it in place, tightening the clamps, and refilling the power steering fluid before reconnecting the battery and starting the engine to check for leaks.
How do you install a amp to a Impala head unit?
To install an amplifier to an Impala head unit, first, disconnect the negative battery terminal for safety. Connect the amplifier's power wire to the car's battery, ensuring a fuse is installed close to the battery. Run the ground wire to a solid metal point on the vehicle, and connect the remote turn-on wire from the head unit to the amplifier. Finally, connect the speaker wires from the amplifier to the speakers, and reconnect the battery.
How do install an amplifier on a Mitsubishi lancer 2011?
To install an amplifier in a 2011 Mitsubishi Lancer, start by disconnecting the negative battery terminal to ensure safety. Run power cables from the battery through the firewall to the amplifier's location, typically in the trunk or under a seat. Connect the amplifier to the car's audio system using RCA cables and speaker wires, ensuring all connections are secure. Finally, reconnect the battery, adjust the amplifier settings, and test the system for proper functionality.
Can a power amplifier amplifies the power?
Question: Can a power amplifier amplify the power? An amplifier can amplify the voltage or the current. Power can be converted to heat.
How does power amplifier differ from a conventional voltage amplifier?
A voltage amplifier does not have to supply significant current bur a power amplifier does.
How to connect amplifier to radio in 96' Chevy Astro?
To connect an amplifier to the radio in a 1996 Chevy Astro, first, disconnect the battery to avoid any electrical issues. Then, locate the radio harness and identify the speaker wires; you can use a wiring diagram specific to your vehicle for accuracy. Connect the amplifier's power wire to the battery, the ground wire to a solid metal point, and the speaker wires from the radio to the amplifier's input. Finally, connect the amplifier's output to the vehicle's speakers and reconnect the battery.
How long will a fully charged 12 volt battery power a 600 watt stereo amplifier?
maybe 30 mins
What is 9-volt battery on backside of bass for?
To power a very small internal amplifier inside the guitar. This is for the active cnotrols.
How do you wire a sub in a saxo?
To wire a subwoofer in a Citroën Saxo, first disconnect the car battery to ensure safety. Connect the positive terminal of the subwoofer to the amplifier's output, then run a power wire from the battery to the amplifier, ensuring it's fused. Ground the amplifier securely to the car chassis, and connect the remote turn-on wire from the head unit to the amplifier. Finally, make sure all connections are secure and double-check polarity before reconnecting the battery.
