0
What else can I help you with?
Can you use 240 volts with a 120 volt supply?
No, it is not possible to use 240 volts with a 120 volt supply directly. You would need a transformer to step up the voltage from 120 volts to 240 volts. Attempting to use 240 volts with a 120 volt supply without a transformer can damage equipment and pose a safety hazard.
Can a 125 volt cable power a 120 volt piece of equipment?
The first thing we have to do is clarify the question. A cable rating of 125 volts is an insulation rating of the wire. Like wire with ratings of 300 volts, 600 volts and 1000 volts these are the highest allowable voltages that can be applied. A wire that is rated for 300 volts is good for 120 volts, 240 volts and 277 volts. At test research facilities, equipment is tested to destruction. The label that is given to wire as a result of the tests is the highest safest voltages that can be applied to that particular wire. So when you see a wire that has a label stating that it is rated for 300 volts it means that any voltage under and up to 300 volts is safe to apply. So to answer the question yes, the 125 volt insulation rating on the cable can be used to supply a source of 120 volts to a 120 volt rated piece of equipment.
Can a car battery light a bulb?
Most car batteries are 12 volts. They can light 12 volt bulbs. The bulbs in your house are likely 120 volt bulbs. A car battery will not light those without some very special equipment, or unless you were to wire ten car batteries in series.
Can you wire a 120 volt ballast to a 347 volt circuit?
No, you cannot wire a 120 volt ballast to a 347 volt circuit. The ballast is designed to operate at a specific voltage, in this case 120 volts, and connecting it to a higher voltage circuit like 347 volts can damage the ballast and pose a safety hazard. It is important to match the voltage rating of the ballast to the circuit it will be connected to.
Does 240 volt have a neutral wire?
Yes <<>> In North America, a three wire 120/240 volt system uses a neutral wire. For 240 volts two "hot" wires are used with no neutral.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
How do you wire 347 volts ballast to 110 volt feed?
You don't. A ballast with a 347 volt input is a commercial ballast. The 347 volts comes from a 600 volt three phase four wire Y system. You can change the ballast out to a 120 volt and rewire the unit but in most cases it is cheaper to buy a completely new lighting fixture.
How do you change a 220 240 volt wire to a 110 120 volt wire?
To change a wire from 220-240 volts to 110-120 volts, you will need to reconfigure the wiring by connecting it to a transformer that steps down the voltage. This transformer will reduce the voltage from the higher range to the desired lower range, allowing you to safely use it with 110-120 volt systems. It's important to ensure the transformer is compatible with the current and wattage requirements of your device or equipment.
Can a 10-2 wire be connected to a 10-3 recepticle for a dryer?
No, the dryer needs 120 volts supplied by the neutral third wire, along with the 240 volts for the dryer element. One of the two 240 volt supply conductors is used with the neutral to supply 120 volts to the controls and the drum motor. That is why a three wire cable is needed.
Why not put a 12 volt motor to replace the 120 volt motor in your freezer Will this work?
The voltage of 120 volts is more common that the lower voltage of 12 volts.
Are auto electric systems 12 volt or 120 volt?
12 Volts DC
What the difference between a 120 volt and a 240 volt waffle iron?
One has an element designed to work on 120 volts, the other has an element designed to work on 240 volts.
