0
What else can I help you with?
How do you tighten a loose strut top nut on an e30 BMW?
impact gun
What causes a knock sound in rear of 2001 Saturn wagon strut system?
A loose strut. There is a nut at the top of the strut that is sort of difficult to tighten. Get a box wrench for the nut and slip it over the strut shaft. Notice the top of the shaft of the strut - it's not exactly round. It's sort of oval, thus enabling you to hold that with vice grips. Place the vice grips on the shaft. Hold the vice and tighten the nut. Don't over tighten Same thing happened to my car. Hope this helps.
How do you tighten the top nut on a strut on a2000daewoo a?
take a close look at the nut, do u see any plastic poking out of the nut and stud area? If u do, then these are not re-useable and will need to be replaced. Also, u will need a torque wrench and tighten to Daewoo's specification. Good luck
The strut rod spins with the nut on top of my strut assembly disabling it from coming loose How do I get the nut on the top of my strut assembly to come off?
The top of the strut rod should be flattened slightly into a rectangular shape. It should be enough that you can take a crescent wrench and hold the flattened part with it. Use an open end wrench for the nut, putting it on first, then the crescent. Turn them opposite directions to loosen the nut.
How do you change rear shock assembly's on a 1996 ford escort lx?
You have to take the whole strut assembly off (shock and spring). Then with a spring compressor on the coil spring, take the top nut off the strut shaft and take the spring off. Once the spring is off the whole strut assembly is replaced which will contain a new shock. Then you already have the spring compressed, so you put the old spring on to new strut (shock) put the top back on, release the spring and tighten the nut. You have to have a vise to clamp the strut into to replace the strut body.
How do you adjust the steering gearbox on a 1996 Chevy Tahoe?
The adjustment is on top of the steering box. Loosen the locking nut then tighten the bolt lightly. Over tightening will cause the box to be too tight.
How do you get to the top nut on the rear strut on a 1992 Toyota Paseo?
take out back seat and trim pieces
How do you changed the spring on a Toyota Camry?
If you mean suspension springs... You need raise your car. Remove the wheel. Remove the strut. Make sure that you have strut spring compressor (you can rent one at Autozone). After that compress the spring until you will able freely rotate to top part of the strut. If the spring is broken you can skip compressing. Remove the center nut. Remove the top part of the strut, replace the spring. Inspect rubber parts, replace if you have to. Align the spring. Compress it. Install the top part aligning it properly (there is an arrow showing outside direction). Tighten it properly. Release the spring. Install the strut.
How are the struts on a 92 Pontiac Le Mans 1.6 liter removed?
unbolst strut from the vehicle. compress the springs with spring tool. take large nut from top of strut assembly. remove spring from assembly. use tool to unscrew the top of the strut cartridge. slide top off of strut piston. take strut cartridge out and replace with new one. then revers the steps.
Why does one of your rocker arm bolt keep backing off when you tighten it down?
dont worry about why, just take another nut with same threads and tighten it on top of the existing nut
How do you change a strut bearing on your mk1 Renault clio?
remove the 22mm bolt at the top that holds the strut to the car DO NOT REMOVE THE 19MM NUT ON THE STRUT ITSELF UNLESS YOU HAVE USED A SPRING COMPRESSOR TO RELIEVE TENSION OF THE SPRING
How do you increase pressure on a pressure reducing valve?
Loosen the nut on top. Tighten the screw clockwise to increase, counter-clockwise to decrease pressure. Tighten the nut back up. Done deal
