0
there are 2 lines on the cams. make them touch each other. with these 2 lines touching each other the cank should be lined up with the tdc stamped on the motor. hope this helps. also these cars aren't fun. i had toremove all 3 motor mounts and jackup the engine just to getin there. also u have to rremove the 2 cams to take out the water pump.a few 6 packs and i got it done.
What else can I help you with?
What are the timing marks for a 2001 Chrysler PT Cruiser?
They are lines and arrows on the sprockets and engine.
Timing marks line up for 1990 Chrysler New Yorker 3.3 liter?
To align the timing marks on a 1990 Chrysler New Yorker with a 3.3-liter engine, first ensure the engine is at top dead center (TDC) on the compression stroke for cylinder one. The timing marks on the crankshaft and camshaft pulleys should align with their respective indicators on the engine block. If they are not aligned, rotate the crankshaft an additional full turn until the marks line up correctly. After the timing marks are aligned, verify that the ignition timing is set according to specifications.
What are the timing marks for Chrysler 300?
timing marks are , marks on camshaft sprocket, an on crankshaft sprocket'.
Where are the timing marks on a 318?
On a Chrysler 318 engine, the timing marks are typically located on the harmonic balancer and the timing cover. The harmonic balancer has a notch or a mark that indicates the timing degree, while the timing cover has a corresponding mark to align with it. To set or check the timing, you would align these marks at the desired timing specification, usually at the top dead center (TDC) for cylinder number one. Always consult the specific service manual for the year and model for precise timing information.
How do you align timing marks on 2000 1.8 Mitsubishi Mirage?
timing marks 1.8lt Mitsubishi 2001
How do you align timing marks on 1.8 Mitsubishi mirage?
how do you align timing mark on 97 1.8 Mitsubishi mirage
Where does the timing marks align on a 1987 2.8 s10?
On a 1987 2.8L S10, the timing marks align on the harmonic balancer and the timing cover. You should look for a notch or mark on the harmonic balancer and align it with the appropriate timing degree mark on the timing cover. Typically, for proper ignition timing, you would align the marks at around 0 degrees BTDC, but always refer to the specific service manual for precise settings.
How do you align the timing marks on 4m51 Mitsubishi canter?
timing on 4m 51 engine
Do all 4 marks on cam sprockets align with straight edge on a Chrysler PT Cruiser engine?
Yes, check to make sure you have the crank sprocket mark lined up with the edge of the tooth, not the center.
Does the marks have to be right on a 2004 Chrysler sebring?
If you are aking about the timing marks on the belt/chain. Then yes.If you are aking about the timing marks on the belt/chain. Then yes.
How do you set the timing on 1995 Chrysler lebaron?
To set the timing on a 1995 Chrysler LeBaron, first ensure the engine is at top dead center (TDC) on the number one cylinder. Next, locate the timing marks on the crankshaft pulley and the timing cover. Align the marks according to the specified timing setting, which is typically around 10 degrees BTDC for this model. Finally, tighten the distributor hold-down bolt and recheck the timing to ensure it remains in the correct position.
You are changing the timing belt and you need o know where the timing marks are for the cam shaft and the crankshaft on a 1994 corolla Also how do you align the marks to put engine in time?
You are changing the timing belt and you need o know where the timing marks are for the cam shaft and the crankshaft on a 1994 corolla Also how do you align the marks to put engine in time?
