0
The term "kicker 450.2" likely refers to a specific model of car audio amplifier, and whether it is "amp ohm stable" typically depends on its specifications. Most amplifiers have a specified impedance range they can handle, usually expressed in ohms, and their stability at different loads (e.g., 2 ohms or 4 ohms). You would need to check the manufacturer's specifications for the Kicker 450.2 to determine its stability at various impedance levels. Generally, reputable amplifier brands like Kicker provide detailed ratings for their products, so consulting the user manual or technical sheet is advisable.
What else can I help you with?
Are kicker L7s good speakers and what kind of amp do I need to power 2-15 inch subs?
Yes, the L-7s are great. For the amp, you first need to find out whether the sub woofers are 2-ohm, 4-ohm, or 8-ohm. Depending on the answer to that question will determine whether or not you'll need a mono amp or a dual channel amp as well as the wattage.
2 channel alpine 500 watt amp hooked up to 12'' comp cvr kicker in a 98 neon why does my amp keep turning off?
probably because you got your amp bridged and its not a stable ohm load
Fosgate amp 400 A4 max power at 1 ohm?
No it's not 1 ohm stable. But it is 2 ohm stereo stable
How much power will a Kicker zx 750.1 amp give a 4 ohm 12 inch kicker L7 sub?
750 watts
Can you run 4 Kicker CVR 4 ohms subwoofers with one amp?
Yes, you can run four Kicker CVR 4-ohm subwoofers with one amplifier, but you need to ensure that the amplifier can handle the total impedance load. If you wire the four 4-ohm subs in parallel, the total impedance would drop to 1 ohm, so you'll need an amp that is stable at 1 ohm and has enough power to drive all four subs effectively. Make sure to check the amp's power rating and match it with the subs' power handling to avoid damage.
What size amp do i need for two 10 inch kicker comp's?
You could go with a 600 watt 2 ch amp or a 300 watt mono block amp, depends on what OHM the subs are, if they are 8 ohm you could wire them down to 4 ohm or if they 4 ohm u could wire them to 2 ohm, i have a 600.1 Boss amp and subs are wired together at 2 ohm and they BANG.
Can you overload a channel on a amp?
Yes you can burn a channel on an amp. Which is do to a overload. Like a 2 ohm load on an amp that is not 2 ohm stable. Will burn out a channel or both channels.
Your Amplifier for your 600 watt sub is cutting out The peak in the amp is 600 watts How do you get it to stop cutting out?
you ohm load is too low. raise the ohm load or buy an amp that is stable at the ohm level of the sub.
What sub should I get for a 1100 watt mono amp can I use two and wire them together how many watts should they be?
Depends on the rms or continuous rating of the amp and at what ohm is the amp stable
How big should the amp be to two 12 subwoofers?
What you need to know is the RMS power rating and ohms of the subwoofer. (Example; RMS is 300 watts and it is a 2 ohm sub. This is what you would need. You have 2 subs so a total of 600 watts. So you want an amp with a max power rating of 600 watts, but he is the tricky part. They were 2 ohm subs. So your amp needs to be 2 ohm stable. No there all not 90% of amps are only 4 ohm stable.)
If you have a 1000 watt 2 ch amp and 2 1000 watt G A 12's how do you set it to 1 ohm?
unfortionatly it alot more difficult than that. you first need to know if your subs are dual or single voice coil. then the ohm of the coils. your next step is to make SURE your amp is one ohm stable. (most are not) if your sub ohm will match you amp ohm. safely. its all in the wireing of the amp to the subs to change the ohms. if you dont know exactly how to wire them DONT DO IT yourself.
How do you reduce the ohms from 4 ohm to 2 ohm ON A 1000 WATT KICKER AMP MONO BLOCK IM RUNNING 2-15 AUDIO PIPE SUBS IN A SEALED BOX. THIS QUESTION IS FOR CAR AUDIO?
put 2 speakers in series
