0
What else can I help you with?
How do you change ball joints on 1991 ford ranger?
You need to remove the spindle and press out the ball joints & press in new ones
How do you replace the ball joints on a 1984 Jaguar XJ6?
To replace the ball joints on a 1984 Jaguar XJ6, start by safely lifting the vehicle and removing the front wheels. Disconnect the lower control arm from the spindle and remove the old ball joint using a ball joint separator or a press. Install the new ball joint by pressing it into place, reattach the control arm to the spindle, and ensure all bolts are torqued to specifications. Finally, reassemble the wheels and lower the vehicle, checking for proper alignment afterward.
How do you fix the ball joint?
replace them when the have play. When replacing them, it is wise to not use a torch on certain ball joints as they will explode.Some basic things about ball joints, by Vertebratefrom the spindle. Sometimes you need a ball joint separator to do that part of the job.My suggestion is to ask "How do you replace ball joints on a "Year, Make, Model"? And hopefully someone has answered the question for that specific vehicle and year.
How do you remove the front spindle from 1986 fiero gt?
Jack up and safely support car Remove the following component's: Wheel, Brake caliper, brake rotor. Disconnect tie rod from spindle Support lower "A" arm with stand etc Remove nuts for upper and lower ball joints. Use an appropriate tool to release the ball joints from the spindle, do not use a fork and hammer as this will damage the joint, there are special tools available for this purpose. Once the joints are released you should only have to heave to get the spindle out.
What is the purpose of a steering knuckle?
With the aid of ball joints and steering joints, the knuckle allows the spindle to move up and down for suspension, rotate left and right for steering.
Is it unsafe to drive a jeep with bad ball joints?
A bad ball joint isn't safe any way you look at it. Some major damage can happen if the wheel becomes dislodged from the chassis. The major component holding the wheels on are the ball joints, upper and lower, which hold the spindle that houses the axle. The spindle holds the wheel bearing, tie rod, brakes, wheel etc. You can lift the vehicle up by the front and check the wheel for play, up and down. There shouldn't be much, if any play. If there is alot of play then you shouldn't drive it much till it get's fixed. That's my opinion. Good luck.
What is the upper and lower ball joint connected to on a 1991 Chevy k1500?
The ball joints are riveted or pressed into the upper and lower control arms, then the spindle is bolted to the ball joints.
Popping noise by the floor bored on the drivers side while pressing the brakes?
check cv joints ball joints tierodends
How do you change a constant velocity joint?
depending on which of the joints you want to change jack up the front of the vehicle and secure have some one apply the foot brakes after you remove the wheels and slacken the securing lock nut on the end of the velocity joint, remove the steering end, and the top part of the spindle, and the bottom ball joint remove the lock nut entirely from velocity joint move out spindle and secure release the strap on the inner both rubber and remove the entire drive axle clean and seperate the joint from the axle the instalation procedure is the reverse.
How do you put the spindel back on the front of 4x4 new balljoints on cant put back on?
To reinstall the spindle on new ball joints for a 4x4, start by ensuring the ball joints are properly seated in their respective control arms. Align the spindle with the ball joint studs and gently tap it into place with a rubber mallet if necessary. Ensure the spindle is correctly oriented and that any alignment marks match up. Finally, secure the spindle by tightening the nut to the manufacturer's specified torque.
How to you change the upper ball joints on a 2001 dodge Dakota fwd?
you have to remove the spindle and press the old ones off
Brakes pulsate and vibrate when stopping it is worse if you are turning while braking?
For the brakes, check for warped rotors. For the turning, check for worn CV joints.
