answersLogoWhite

0

i just did a timing belt change on 1991 crx. according to my manual the tensioner bolt should be 33 foot pound or about 400 inch-lbs torque.make sure you use a six pointed 14mm socketso you won't round out the bolt head. since your a/c mount bolts are stationary they should be tightened about two hundred inch pound; your a/c belt should have 1/8 to 1/4 inch detent on the longest part of the belt and then tighten the nut on the pulley then tighten the adjustment screw. hope this help

User Avatar

Wiki User

18y ago

What else can I help you with?

Related Questions

What is the torque setting for 2005 impala drivebelt tensioner bolt?

no adjustment for belt tension ~ spring loaded. pulley mounting (spindle) bolt = 57 ft-lbs.


How do you replace the belt tensioner on a 1998 Dodge Ram 1500 5.9L 4WD?

REMOVAL WARNING: BECAUSE OF HIGH SPRING PRESSURE, DO NOT ATTEMPT TO DISASSEMBLE AUTOMATIC TENSIONER. UNIT IS SERVICED AS AN ASSEMBLY (EXCEPT FOR PULLEY). (1) Remove accessory drive belt. (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - REMOVAL). (2) Disconnect wiring and secondary cable from ignition coil. (3) Remove ignition coil from coil mounting bracket (two bolts). Do not remove coil mounting bracket from cylinder head. (4) Remove tensioner assembly from mounting bracket (one nut) (Fig. 4) (5) Remove pulley bolt. Remove pulley from tensioner. INSTALLATION (1) Install pulley and pulley bolt to tensioner. Tighten bolt to 61 N·m (45 ft. lbs.) torque. (2) Install tensioner assembly to mounting bracket. An indexing tab is located on back of tensioner. Align this tab to slot in mounting bracket. Tighten nut to 67 N·m (50 ft. lbs.) torque. (3) Connect all wiring to ignition coil. CAUTION: To prevent damage to coil case, coil mounting bolts must be torqued. (4) Install coil to coil bracket. If nuts and bolts are used to secure coil to coil bracket, tighten to 11 N·m (100 in. lbs.) torque. If coil mounting bracket has been tapped for coil mounting bolts, tighten bolts to 5 N·m (50 in. lbs.) torque. (5) Install drive belt. (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - INSTALLATION). (6) Check belt indexing marks (Fig. 4).


2003 suzuki xl7 how do you adjust the belt tensioner?

To adjust the belt tensioner on a 2003 Suzuki XL-7, first, locate the tensioner pulley. Use a socket and ratchet to turn the tensioner pulley counterclockwise to relieve tension on the belt. If the tensioner is adjustable, you may need to loosen the mounting bolts to reposition it; otherwise, check for proper tension and replace the tensioner if it’s worn out. Always refer to the vehicle’s service manual for specific procedures and torque specifications.


Torque specification on 1997 powerstroke belt tensioner and idler pulley?

40 lbs-ft (+/- 5 lbs-ft)


How do you set the timing on 2002 Kia Rio?

This is the procedure for installing the timing belt, and contains the info on where all marks need to be set for proper timing: Install : 1.Install tensioner pulley 2.Pull tensioner pulley to its furthest point and tighten lock bolt. 3.Check that timing mark on timing belt pulley is aligned with timing mark on engine http://msw.kiausa.com/data/manual/sh...G/lc3b620a.gif 4.Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate. http://msw.kiausa.com/data/manual/sh...G/lc3b620b.gif 5.Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order. 6.Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys. 7.Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt. 8.Tighten tensioner pulley lock bolt to specified torque. Tightening torque:28~38 lb-ft (38~51 N


Is the belt tensioner pulley on a 1998 olds 88 reverse threaded?

No, the belt tensioner pulley on a 1998 Oldsmobile 88 is not reverse threaded. It typically has a standard right-hand thread for the bolt securing it. If you're replacing or adjusting the tensioner, ensure you turn the bolt counterclockwise to loosen it. Always refer to a service manual for specific details and torque specifications for your vehicle.


How do you adjust the idle pulley on a 1996 Plymouth Grand Voyager?

== # Loosen the idler pulley lock nut # Turn the adjusting screw to lower the idler pulley # Remove A/C belt. == # Install A/C belt over pulleys. # Apply a snug torque to the idler pulley lock nut. # Turn adjusting screw until proper belt tension is obtained. # Tighten idler pulley lock nut to 54 N·m (40 ft. lbs) == The Poly-V generator/power steering pump belt is provided with a dynamic tensioner. == WARNING: DO NOT ALLOW DRIVE BELT TENSIONER TO SNAP BACK, AS DAMAGE TO TENSIONER AND/OR PERSONAL INJURY COULD RESULT. # Remove air conditioning belt. Refer to procedure in this section. # Apply a force in a clockwise direction to the tensioner pulley bolt # Remove belt. == # Install belt over all pulleys, except for the tensioner pulley. Refer to for belt routing. # Apply a force in a clockwise direction to the tensioner pulley bolt # While holding tensioner, position belt over tensioner pulley. # Slowly release force on tensioner. # Verify belt is properly routed and engaged on all pulleys.


What is the torque pounds when installing anew water pump and pulley on a 1986 lesabre?

Long mounting bolts 22-29 ft lbsShort mounting bolts 96 - 132 in lbsPulley bolts 108 - 132 in lbs


Is a tensioner pulley bolt reverse thread on a 98 Kia Sephia?

No, the tensioner pulley bolt on a 1998 Kia Sephia is not reverse thread; it is a standard right-hand thread. When removing or tightening the bolt, you should turn it clockwise to tighten and counterclockwise to loosen. Always refer to the vehicle's service manual for specific torque specifications and procedures.


Why does the tensioner bolt keep breaking on my 2001 Ford Escort ZX?

An accessory or idler pulley is frozen or in very bad shape and is snapping the tensioner and bolt from all the torque being applied to it. Check all your pulleys when you have it off. They should rotate freely.


How do you change the serpentine belt in your 2002 Hyundai xg350?

There are two belts - one to drive the power steering pump near the firewall and the other to drive the alternator and A/C compressor. Each belt has a tensioner. To change, raise front passenger side of car and put on jackstand. Remove wheel/tire and remove splash shield which will give access to the belts and tensioners. Loosen mounting bolts in the center of tensioners, then loosen the tensioner adjustment bolts which can be reached from the bottom of the tensioner. Remove belts, put new ones on and re-tighten the tensioner adjustment bolts. Then re-tighten the tensioner mount bolts to torque spec. All torque specs can be found in the freely available maintenance data available from Hyundai at www.hmaservice.com.


How do you adjust Mazda MX3 AC and PS belt?

To adjust the AC and power steering (PS) belt on a Mazda MX-3, first, locate the tensioner pulley for the belt. Loosen the tensioner bolt, then adjust the tension by either moving the tensioner or adjusting the mounting bolts of the components. The belt should have about half an inch of deflection when pressed firmly in the middle; readjust and tighten the bolts once the correct tension is achieved. Always refer to the vehicle’s service manual for specific torque specifications and procedures.