answersLogoWhite

0

The alternator brackets on a 1986 Mazda B2000 typically use 10mm bolts. However, it's important to verify the specific design and any modifications that may have been made to the vehicle, as variations can occur. For precise sizes and specifications, consulting the vehicle's service manual or a parts retailer can provide the most accurate information.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

Change alternator in Mazda 6?

Disconnect the battery Remove the engine covers to access the alternator drive belts. Remove the electrical connections from the alternator. Slacken the bolts, remove the belt. Remove bolts, put new alternator on, tighten bolts until you can just move alternator, fit new belt, move alternator so the belt is tight and then tighten bolts to their specified torque.


How to removed Toyota Echo alternator the both upper and lower bolts pulled out but alternator never come out?

Most alternator brackets will have moveable bushings (short sections of pipe usually with a slot in them, in one of the engines brackets) that pinch onto the alternators mounting lugs tightly even after the bolts are removed, you should be able to pry the alternator free, tapping on the engines brackets (next to bushing not the bushing its self) may aid removal, be carefull some are cast aluminum and are breakable.


What are the torque specs for the head bolts of a 1986 Mazda B2000?

For the 1998cc, from the AllData manual "copy": 80-86 N-m (59-64 ft-lb).


How do you tighten alternator belt on 2001 Mazda mpv?

To tighten the alternator belt on a 2001 Mazda MPV, first, locate the alternator and loosen the mounting bolts. Then, adjust the alternator's position to increase the tension on the belt. Once the desired tension is achieved, re-tighten the mounting bolts securely. Finally, check the belt's tension by pressing down on it; it should have a slight give but not be overly loose.


How do you put on an alternator belt on 1991 Mazda mx6?

To install an alternator belt on a 1991 Mazda MX-6, first, ensure the vehicle is off and safely supported. Loosen the alternator mounting bolts to allow for adjustment. Route the new belt around the alternator and the crankshaft pulley, ensuring it sits in the grooves properly. Finally, adjust the tension by moving the alternator, tighten the bolts, and check the belt alignment before starting the engine.


How do you change alternator belt on a 1988 Mazda 626?

To change the alternator belt on a 1988 Mazda 626, first, disconnect the negative battery cable for safety. Locate the alternator, then loosen the tensioner bolt and the mounting bolts on the alternator to relieve tension on the belt. Remove the old belt and install the new one, ensuring it sits properly on the pulleys. Finally, retighten the alternator bolts, adjust the tension as needed, and reconnect the battery cable.


How many bolts hold the starter on your 1988 B2000 pickup?

2 bolts hold it on


How do you change the alternator belt on a Mazda 323?

To change the alternator belt on a Mazda 323, first remove the right hand air shield under the can. Then locate the pulley tensioner of the AC and loosen the bolts on the pulley. Finally, remove the alternator pivot bolt under the alternator to remove the old alternator belt and replace with a new one.


How do you change the alternator belt in a 1996 Mazda protege?

What bolts to loosen to put alernator belt on and how to put it on when a/c belt is on.


How do you change the alternator belt on a Mazda rx-7?

To change the alternator belt on a Mazda RX-7, first, ensure the engine is off and cool. Loosen the alternator mounting bolts and the tensioner bolt to relieve tension on the belt. Remove the old belt and install the new one, ensuring it is routed correctly around the pulleys. Finally, adjust the tension on the new belt by repositioning the alternator before tightening all bolts securely.


Changing alternator in 1993 Mazda 626?

Remove the positive cable from the battery post. Remove the cables from the alternator. Remove the alternator wiring harness. Remove the belt by loosening the tensioner pulley. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


How do you put an alternator belt on a Mazda mx3?

To put an alternator belt on a Mazda MX-3, first, disconnect the battery to ensure safety. Loosen the alternator mounting bolts to allow for adjustment and then remove the old belt. Position the new belt around the alternator pulley and any other pulleys as needed, then adjust the alternator to achieve proper tension before tightening the mounting bolts. Finally, reconnect the battery and check the belt alignment and tension before starting the engine.