0
What else can I help you with?
Do 15 watt speakers go well with a Kenwood four channel amplifier?
No, 15 watt speakers are rated far to low to be used with an external amplifier.
What speaker match a 1600 watt rms 2 channel amplifier?
To match a 1600 watt RMS 2-channel amplifier, you should look for speakers that can handle a power rating of at least 800 watts RMS per channel, assuming a standard setup where each channel drives one speaker. It's also important to consider the speaker's impedance; typically, 4-ohm speakers are a good match for higher power amplifiers, as they can draw more power. Additionally, ensure the speaker's sensitivity rating is suitable for your listening environment to achieve optimal performance.
How many watt amplifier will power two 15 inch speakers?
It depends on the power handling capability of the speakers. Generally, a 500-600 watt amplifier would be sufficient to power two 15-inch speakers that have a power handling capacity of around 250-300 watts each. Make sure to match the amplifier's power output with the speakers' power handling to avoid damaging the speakers.
Can a 15 watt amplifier power 300 watt speakers?
Yes it can. The rated power of the speakers is the MAXIMUM that can be applied. If more power is supplied, damage can occur. Either the speech coil can blow or mechanical damage to the cone or suspension units.As the amplifier is below this rating, it will not supply more power than the speakers can handle and will be perfectly safe.
Can you use a 5800 watt amplifier with 2 12 inch 1400 watt woofers?
Yes, you can use a 5800-watt amplifier with two 12-inch 1400-watt woofers, but it's important to match the amplifier's output to the speakers' power handling to avoid damage. If the amplifier's power significantly exceeds the woofers' ratings, you may need to be cautious with volume levels to prevent overpowering the woofers. Additionally, ensure that the impedance of the woofers matches the amplifier's output specifications for optimal performance.
Can you use a400 watt speaker with150 watt amp?
You can, but the problem is your speakers will not give their optimal sound quality because your Amplifier is too weak for the speakers. So,buy an amplifier with an output power rating high then 400w.
Can you run speakers with an amplifier that has a bigger rms rating than the speakers rms rating For example run an 80 watt rms speakers with a 120 watt rms amplifier?
Yes you can. Contrary to popular belief, an amplifier rated with a higher output than the speaker rating rarely damage the speakers. If the amplifier overdrives the speakers, the sound quality will be dramatically affected. Most listeners will turn the level down to reduce the distortion being heard. The amplifier's power rating is the maximum power that it can produce and it does not mean the output power will be at that level. On the other hand, an amplifier that is overloaded will deliver distorted signals to the speakers. At high power levels, the distortion can be damaging to the speakers in a way that simply over driving a speaker is not. Therefore, it is as safe to use an overpowered amplifier with speakers as it is an amplifier that is rated at the same power or even lower power than the speakers.
What size amp for two 600 watt speakers?
To properly power two 600-watt speakers, you'll want an amplifier that can deliver at least 600 watts per channel at the speakers' impedance (usually 4 or 8 ohms). A good rule of thumb is to choose an amp with a power rating of 1.5 to 2 times the speaker's RMS rating for headroom and to avoid distortion. Therefore, an amplifier rated between 900 to 1200 watts per channel would be ideal for optimal performance. Always check the compatibility of the amp with your speakers' impedance and power handling specifications.
How big of amp to run 650 watt speakers?
Speaker wattage is a measure of the power handling capability of the speaker. This assumes a clean un-clipped signal from the amp. The spec you need is Sensitivity: Sound Pressure Level (in db) with 1 watt input of a 1khz signal measured at distance of 1 meter from the speaker. Highly efficient speakers are going to be around 96/98 db. If your speaker is rated at 93 db 1watt/1meter, then it will take twice as much amplifier power to run it up to 96 db. Depending on whether you want your ears to bleed, most speakers will do quite well with 100 watt or so high quality amplifiers. Keep in mind, if you want extreme volumes get a 200/300 watt amp or better to give you the headroom needed to keep signals from clipping and blowing your speakers. This answer assumes the question was for home stereo.
How is the amplifier watt rated for example if its 350 watt and 2 channels does it produce a 350 watt at each channel or is it divided on the 2 channels so that it would be 175 watt for each channel?
if it is 350 rms by 2 channels it is 175 rms each channel unless it can be bridged than its 350 rms by 1 channel
Can you use a 600 watt amp with a 500 watt subwoffer?
Yes, you can use a 600 watt amplifier with a 500 watt subwoofer. It is important to ensure that the amplifier's output power does not exceed the subwoofer's power handling capability to avoid damaging the subwoofer. It is also recommended to properly set the gain levels on the amplifier to match the subwoofer's power handling.
What maker or model amplifier is a KA-1460B 4 Channel 800 Watt amp?
The maker or model amplifier that is a KA-1460B 4 channel 800 watt amp is Dual Electronics. Dual Electronics is the maker of high quality home, marine, and car audio solutions.
