answersLogoWhite

0

What else can I help you with?

Related Questions

What is rem in amplifier?

'Rem' stands for remote, you connect a turn on lead to it so the amp knows to power on.


How do you install a amp to a Impala head unit?

To install an amplifier to an Impala head unit, first, disconnect the negative battery terminal for safety. Connect the amplifier's power wire to the car's battery, ensuring a fuse is installed close to the battery. Run the ground wire to a solid metal point on the vehicle, and connect the remote turn-on wire from the head unit to the amplifier. Finally, connect the speaker wires from the amplifier to the speakers, and reconnect the battery.


Can i use the same power from my amp.to remote wire for power?

Using the same power from your amp to power the remote wire is not recommended. The remote wire is designed to send a low voltage signal to turn the amplifier on and off, while the power wire carries the main current needed for the amplifier's operation. If you draw power from the same source, it could lead to inadequate voltage for the remote wire, causing the amplifier to malfunction or not turn on properly. It's best to keep the power and remote wires separate for optimal performance.


What should you plug in the remote wire into in a Bonneville?

As always, either the power antenna or the remote turn-on for an amplifier.


How do you connect IC in power amplifier?

Check the datasheet for pinout.


Connect a 12v wire to an amplifier?

Ensure the amplifier is turned off. Connect the positive (+) terminal of the 12V wire to the amplifier's positive terminal and the negative (-) terminal of the 12V wire to the amplifier's negative terminal. Once connected securely, you can then power on the amplifier.


How do you wire a sub in a Saturn sc?

Connect the sub woofer to the equalizer or amplifier. The positive wire will need to be connected to a power source. Connect the ground wire. Connect the auxiliary wire to the amplifier.


How to Install an Amplifier?

Installing a Car AmplifierCar amplifiers can greatly enhance the sound quality in a car audio system. They are used to further power the existing speakers and to power additional units such as subwoofers.Before the Installation1- The first thing to do when installing an amplifier in your vehicle is to figure out where the amplifier will be. It can be placed anywhere inside the car however the most common places are in the trunk or under the passenger's seat.2- Next you will need to purchase the correct wiring for your specific amplifier. The thickness of the power cable will vary depending on wattage required. You will also need a ground cable that is long enough to reach the amplifier, an RCA signal cable that will go from the head unit to the amplifier, a 'remote on' wire and a speaker wire.3- Gather the correct tools needed for the installation; a screwdriver, wire cutters, pliers, sandpaper, a utility knife, masking tape and 2 crimp-on o-ring ends to protect the ground and power cables.Installation1- Disconnect the ground cable from the battery.2- Connect the side with the positive power cable to the positive connector on the battery, place the ring-o on this connector and then install the fuse.3- Reach the cable to the area where the amplifier will be.4- Using a metal bolt or screw near the amplifier, connect the ground cable to it using a ring-o. Make sure to clean the metal with the sandpaper beforehand.5- Removing the head unit, connect the signal and remote on wires from the head unit to the amplifier. Then connect the RCA connectors and the remote on wire to the head unit.6- Bringing the speaker wires from the speakers to the amplifier, connect them by first stripping a quarter inch of the wire tip then connecting them to the amplifier using pliers. Make sure to connect the positive with the positive and the negative with the negative.7- Now attach the amplifier safely to the car so it will not move while driving.8- Reconnect the car battery and try it out.If the audio system does not function, make sure that the amplifier is properly grounded. This is the most common reason that it will not work.


How to connect amplifier to radio in 96' Chevy Astro?

To connect an amplifier to the radio in a 1996 Chevy Astro, first, disconnect the battery to avoid any electrical issues. Then, locate the radio harness and identify the speaker wires; you can use a wiring diagram specific to your vehicle for accuracy. Connect the amplifier's power wire to the battery, the ground wire to a solid metal point, and the speaker wires from the radio to the amplifier's input. Finally, connect the amplifier's output to the vehicle's speakers and reconnect the battery.


What are the steps behind installing a car audio capacitor?

First, the capacitor must be charged. Use a voltmeter, and when it reaches 12 volts, the capacitor is charged. The capacitor should then be installed near the car audio amplifier. Keep the negative wire attached to the battery. Then, a ground wire from the negative post on the capacitor to the car's chassis on the chassis's bare metal ground point. Next, the power wire needs to be disconnected from the amplifier's power input. Connect the wire to the positive post on the capacitor. A new power wire needs to be connected from the capacitor's positive post to the amplifier's power input. Install a 16 gauge wire from the capacitor's remote turn-on post to the amplifier's remote input. Then disconnect the negative wire from the battery.


Can a power amplifier amplifies the power?

Question: Can a power amplifier amplify the power? An amplifier can amplify the voltage or the current. Power can be converted to heat.


Do you need REM cable to power up amp?

Yes, you need a cable to connect the power supply to the amplifier, but the specific type of cable required depends on the model and power requirements of the amplifier. In most cases, a standard power cord with the appropriate voltage and current rating will suffice. It's always recommended to refer to the amplifier's user manual for the correct power supply requirements.