0
What else can I help you with?
What if your 1992 Chevy silverado is leaking engine coolant from the top of the engine just below the distrubutor what is leaking?
There is a heater hose that goes to the left rear top side of the intake manifold and that fitting leaks engine coolant sometimes and it will run down the back of the intake around the distributor. If that fitting is not leaking then the intake manifold gasket is leaking coolant in the corners of it. REplace the intake gasket. That's all that can leak coolant on that year engine. If coolant is leaking out between the transmission and engine block then you have a freeze plug leaking in the back of the engine, between the transmission and block. Must remove the transmission and flywheel to fix it.
How do you change a coolant temperature sender on 1992 ford ranger 3.0 engine?
To change the coolant temperature sender on a 1992 Ford Ranger with a 3.0 engine, first ensure the engine is cool and disconnect the negative battery cable. Locate the coolant temperature sender on the engine block, typically near the thermostat housing. Use a wrench to unscrew the old sender and then install the new one, being careful not to overtighten. Finally, reconnect the electrical connector and the negative battery cable, and check for leaks after refilling any lost coolant.
Where is the coolant temp sensor on your 1992 ford F250 with a 5.8L?
The 1992 Ford F2 50 pickup truck 5.8 liter engine coolant temperature sensor can be found on the top of the engine. The coolant temperature sensor will be near the intake manifold.
Where is the engine coolant sensor located on a 1992 Pontiac transport van 3800?
The engine coolant temperature sensor on a 1992 Pontiac Transport van with a 3800 engine is typically located near the thermostat housing. It is usually positioned on the engine block, close to the intake manifold, and may be accessible from the front of the engine. To locate it, you may need to remove some components for better access, as it can be somewhat hidden. Always refer to a repair manual for specific diagrams and detailed instructions.
Where is coolant reservoir on a 1992 Lexus ES300?
Coolant reservoir, or directly in the radiator. If you are having to add much coolant, you need to find out why. Serious engine damage can occur if it is leaking inside the engine.
Whats wrong if a 1992 Lexus es300 engine coolant bubbling?
headgasket leak and exhaust gas is getting into the coolant
1992 mr2 where is the engine number located on a 3sge engine its an import?
The number is on the block and isjust above where the gearbox connects to the block
What coolant does the 1992 Dodge spirit V6 engine use?
An Spirit engine doesnt use any spacific type of coolant, as long as its a 50/50 mix.
Where is the engine coolant temp sensor located on a 1992 ford f250?
what engine? most will be close to the t-stat.
Where do you find a cooling sensor on a 1992 g20?
On a 1992 G20, the cooling sensor, commonly known as the coolant temperature sensor, is typically located near the engine block, often on the intake manifold or cylinder head. It's usually positioned in a place where it can directly measure the temperature of the engine coolant. To access it, you may need to remove some components or covers in the engine bay for better visibility. Always consult your vehicle's service manual for the exact location and procedures.
Where is the starter on a 1992 Crown Victoria?
down by the bellhousing at the rear of the engine block
How do you change a 1992 Toyota Previa thermostat?
To change the thermostat in a 1992 Toyota Previa, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant, then locate the thermostat housing, which is typically near the engine block. Remove the housing by unscrewing the bolts, take out the old thermostat, and replace it with the new one, ensuring the rubber gasket is properly seated. Reassemble by reversing the steps, refill the coolant, and check for leaks.
