0
What else can I help you with?
How do i replace the battery cable ends on Toyota matrix?
To replace the battery cable ends on a Toyota Matrix, first ensure the vehicle is off and disconnect the negative battery terminal followed by the positive terminal. Use a wrench to remove the old cable ends from the battery and cut off any damaged wire if necessary. Strip the ends of the wires to expose fresh copper, then attach the new cable ends by crimping or soldering them securely. Finally, reconnect the positive terminal first, followed by the negative terminal.
How do you change the positive battery cable on a 1994 Chevrolet C series 1500 truck?
Disconnect the positive cable at the 95 1500 battery. Follow the cable to the other end and look at how it was routed. Unhook the cable end and pull it out. Route the new cable in the same way. Connect the cable ends back up.
Show a Wiring diagram for 2x12 volt batteries in series?
No, but I'll tell you how to do it... Put the two batteries in the truck. Call them "1" and "2." Hook the positive cable from the truck to the positive of battery 1, the negative cable from the truck to the negative of battery 2, and the series-wiring cable (it's about a foot long, and it's got a battery clamp at both ends) between the negative on battery 1 and the positive on battery 2.
How do you change the positive battery cable on a Honda Civic Ex?
Disconnect the cable from the Civic battery. Trace the wire to the other end, paying careful attention to the routing. Disconnect the cable at the far end, and pull the cable out. Put the new cable in following the same path. reconnect the cable ends.
What is involved to changing a battery in 2001 S10 pickup?
Using a 5/16" 6 point box wrench or socket remove the negative battery cable first then the positive cable. Using a 13mm socket with a 10" extension remove the battery hold down bolt and remove clamp wedge. Remove the battery, clean up battery tray and cable ends with water and baking soda and wire brush. Install new battery, reinstall battery clamp and bolt. Attach positive battery cable first then negative cable. You will need to reset clock and radio settings.
How do you replace 2002 Hyundai Santa Fe battery cable?
To replace the battery cable on a 2002 Hyundai Santa Fe, first, disconnect the negative terminal of the battery to ensure safety. Next, locate the positive and negative battery cables; use a wrench to loosen the bolt at the terminal ends and remove the old cables. Install the new battery cables by connecting the positive cable first, followed by the negative cable, and tighten them securely. Finally, reconnect the battery and ensure everything is functioning properly.
What causes the negative cable on a 1982 Honda goldwing to short out?
The negative battery cable will short out if it is loose or corroded. Check both ends of the battery cable for corrosion. Make sure both ends are tight.
How do you change the positive battery cable on a Chevy Venture?
1. Disconnect the battery ground cable. 2. Disconnect the battery positive cable. 3. Remove the battery positive cable nut from the accessory wiring junction block. 4. Remove the battery cable from the starter motor BAT terminal. On the 2002 Venture, The positive battery terminal also supplies power to the circuit breaker and relay assembly located at the left corner of the engine compartment right over the battery. The battery cable for this vehicle is a "factory only" replacement part and is very expensive, in the neighborhood of $130.00 and tax. A perfectly satisfactory alternative is to use a generic battery cable of the right length connected from the battery to the starter motor, and a generic battery cable with ring terminals on both ends connected from the starter motor back to the circuit breaker/relay box. This alternative is an exact electrical equivalent of the factory part, works great, and saves a bunch of both time (ordering part) and money. Good luck!
How do you change the battery cables in a Ford Mercury Mystique?
the whole cable or just the cable ends ??????????????
How do you remove the battery?
First, disconnect the negative (ground) cable from the battery. Next, disconnect the positive cable from the battery. Using a socket wrench with an extension, loosen or remove the battery hold-down clamps at the bottom of the battery. There are two clamps, on opposite ends, that pinch against a ridge on the bottom of the battery. the clamps and ridge are designed to keep the battery from bouncing out of the holder as the vehicle encounters rough roads.
How can you tell which is positive and which is negative on a battery?
Well the flat of the battery is the negative side.
Why did you lose your lights gauges igntion etc when all you did was replace battery cable ends?
It probably wasn't the ends to begin with. Start looking for loose wires starting with the ends if the battery tested good.
