0
In the Daewoo Matiz 800, the knock sensor is typically located on the engine block, often near the cylinder head. It is usually positioned on the side of the engine, where it can effectively detect vibrations from the combustion process. To access it, you may need to remove some engine covers or components, depending on the specific layout of your model. Always consult the vehicle’s service manual for precise location and instructions.
What else can I help you with?
How much does a Daewoo matiz weight?
about 800 Kg.
How much fuel does a matiz daewoo consume?
i have owned a matiz 800 cc for a few months , i get around 40 mpg in buzy town traffic and 55 - 60 on long runs i love my matiz it seems to run forever on £10 of petrol
What size is the fan belt for daewoo matiz 800cc?
The fan belt size for a Daewoo Matiz 800cc typically measures about 6PK800, which indicates it has a 6-rib design and a length of approximately 800 mm. However, it's always best to verify with a specific vehicle manual or parts supplier to ensure accuracy, as variations may exist.
How do you adjust the fuel mixture rich or weak for a daewoo matiz 800?
To adjust the fuel mixture on a Daewoo Matiz 800, locate the fuel mixture screw on the carburetor, if equipped. Turning the screw clockwise typically enriches the mixture, while turning it counterclockwise weakens it. It's essential to make small adjustments and monitor the engine's performance, such as idle stability and acceleration. Always consult the vehicle's service manual for specific instructions and settings.
What are the torque settings for the cylinder head bolts on a daewoo matiz 800?
The torque settings for the cylinder head bolts on a Daewoo Matiz 800 are typically around 20 Nm (15 lb-ft) for the initial pass, followed by a further tightening to 90° for the final pass. It's important to follow the specific sequence for tightening to ensure even pressure across the cylinder head. Always consult the vehicle's service manual for the most accurate and detailed specifications.
Can 2001 Mazda millenia be inspected with knock sensor light on?
yah, but it wont pass. Won't pass in GA, Cost me 170 for the part + 800 for Labour Have fun with that, I know I did M
Where is the knock sensor located on a 95 Mazda millenia 2.3l engine?
lucky for you, it is under the compressor. 5.2 hrs book labor. it takes me at least twice that, plus you gotta have a special socket to get that sucker off. and if you just pound on a deep socket, you still lose, because you will never get it back on unless you have the special socket. Yah Lucky for you the '99 2.5L is INSIDE the manifold and it turns into an 800 dollar job you CANT do on your own. M who ever told you the knock sensor is inside the manifold is probably the same place that told you it is an interference motor. and 800 bucks labor on a 2.5 is about 2x what it should cost. the knock sensor on the 2.5 is WAY easier to get at than the 2.3
Where can you get a camshaft position sensor for a 2000 Daewoo Lanos?
GM is now importing parts for Daewoo's You can get one for $40 plus shipping Call 800 373 7273 Chevrolet's Aveo is the same drivetrain & transmission as a Daewoo Lanos. Order the sensor from any Chevy dealer --but expect a hassle. They will pry and pry about what the VIN number of your "Aveo" is. Tell them it is an '04 equipped with an E-Tech 1 engine. This earlier sensor will fit. The same thing happened to me. GM in North America does not offer parts for vehicles sold under the Daewoo brand name from 1999-2002. In Canada, the only authorized source for Genuine Daewoo parts is Solvit, 60 Esna Park Drive, Unit 5, Markham Ontario. Contact information is available on their website at www.solvit.ca. If you're in Canada, you can get 1 from the Canadian importer for Daewoo Parts - Solvit APC in Markham, Ontario - phone 905-947-8540, fax 289-333-0081, email parts@solvit-apc.ca
What is the torque settings for big end and mains on bearings for 800 cc matiz?
the big end bearings torque down at 55 - 65 Nm
Show you a picture of where the Mazda millenia knock sensor is located?
No, Depends on the year and model. I can however speak for the 99 2.5L It is buring deep in the Manifold and the average DIY cannot fix this one. I spent 160+/- for the part and 800 for the Labour. Good Luck
What type of aircraft will flyglobespan use on the Boston-Knock route?
I've heard a 737-800?? How true i don't know. Damo
Where is the location of the fan sensor on 2002 Chevy Trailblazer?
Where is the location of the cooling fan sensor on a 2002 Chevy Trailblazer? Also what is the 800 number for Chevy?
