0
What else can I help you with?
Why would one headlight not work on low beam but both work on high beam on a 2001 Ford Ranger?
change the light bulb that does not go on, on low beam, it possible that the wire inside the bulb for low beam is broken
How do you change truck headlight bulb change?
headlight bulbs changed,dimmer swich changed,headlight swich changed.key off headlight work low ,key on goes to brights. unpluged harness check ok at first ,but after a few try hi beam indictor would not go to low m-beam
How much does it cost for a low beam headlight for a 1997 frod escort sport?
20 dollars or just go to your local wreckers and get one cheap.
Why would the parking and signal lights go on and the headlights does not on a Chevy S10 truck?
The headlights are a separate circuit from the others. Check the bulbs, headlight switch, Hi/Low beam switch and depending what year you have check the fuses.
2001 Lincoln LS ABS and AFS light?
On a 2001 Lincoln LS, the ABS light means that there is a problem with the brake system. The AFS light on means that there is possibly a headlight that is bad or the headlight will not go from low to high beam or vice versa.
Why does the low beam lights go out when you turn your high beams on your 2003 Pontiac Aztec?
In a 2003 Pontiac Aztek, the low beam lights go out when you switch to high beams because of the vehicle's lighting design. The high beam circuit takes priority over the low beam circuit, meaning that only one set of headlights can operate at a time. This is a common feature in many vehicles to ensure adequate power distribution and prevent overload. If you find that the low beams aren't functioning at all, it could indicate a problem with the headlight switch or wiring.
When i turn on brights on my 05 impala low beam goes out?
When i turn on brights on my 05 impala low bean goes out
How do you remove the headlight switch on a Mercedes E320?
I want to change my low beam left side light on my Mercedes E320 can i change this myself or do i need to go to a dealer i already bought the replacement bulb myself
Why would your car's high beams work but not your low beams?
Possibly two bulbs, possibly the switch. Get it diagnosed. check your fuses for your headlights. i have a '97 accord and installed aftermarket headlights and one day one of my lowbeams wouldn't work but my high beams would be on with my low beams on, and when i switched for the highbeams, my low beams would both go out. you can get a thing at shucks, or even walmart, to check the fuse to see if it's working, very simple to use. :) Did you try replacing the one headlight that only works on the high beam mode? First check to see if you have a relay. If it dont have one, the problem lies on the dimmer switch. Locate the dimmer switch. On some vehicles the dimmer switch is part of your headlight switch. If only one of your headlights is affected then it probably isn't a fuse or relay. A light that is both a low beam and a high beam has two filaments. One of the filaments is probably broken. Replace the headlight and it should fix the problem. i did replace the lamp on a 96 sunfire and the low beam still does not function. highbeams work fine, but no low beams on both headlights now. I have a similar problem. Both headlights low beam filaments on my WRX STi had blown and the replacement low beam filaments blew too??? So I've still only got high beam which is fine but other drivers are getting a wee bit annoyed (and rightly so)All fuses are good and correct factory ampage. The new bulbs are H4's which is the factory correct bulbs yet low beam filaments gone on both bulbs. I'm bewildered...
Why do your low beam lights go out when you put your high beams on?
to draw energy from batteries for HI beam instead of low beam, its kind of like saying why cant i jog when i start to run
Why would both headlights on a 2001 escape go out?
Bulbs burnt out? Bad hi-low beam switch? Voltage spike?
1988 crown Victoria all headlights go out on low beam but work on high beam?
As silly as it sounds, both low beam bulbs are most likely blown. If not, check switch in the steering column.
