0
Yes, the vehicle can be safely operated
HO2S (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)
symptoms
Other than the MIL light illuminating you may not notice any performance issues.
cause
A short in the O2 sensor heater circuit or the sensor itself
A faulty O2 sensor heater
Wiring or connectors are broken or frayed to the sensor or relay
Bad PCM or ECM
The fix
Correct wiring short or loose connector found in inspection.
and/or
Replace the bank 2 sensor 1, O2 sensor
Replace PCM if circuit has failed and no wiring issues present, good O2 sensor
What else can I help you with?
How do you replace a speed sensor on a 1996 Subaru Outback?
To replace the speed sensor on a 1996 Subaru Outback, first, ensure the vehicle is safely elevated and secure. Locate the speed sensor, which is typically found on the transmission or near the vehicle's speedometer cable. Disconnect the electrical connector and remove the retaining bolt to take out the old sensor. Install the new sensor by reversing the process, ensuring a secure fit, and reconnect the electrical connector.
Where is fuel filter located on 2002 Subaru outback?
On a 2002 Subaru Outback, the fuel filter is typically located along the fuel line, under the vehicle. It is often found mounted to the chassis, just in front of the fuel tank or near the rear axle. To access it, you may need to lift the car safely and remove any protective covers if present. Always refer to the owner's manual or a repair guide for specific details and safety precautions.
How to replace rear struts on 2001 Subaru Outback?
To replace the rear struts on a 2001 Subaru Outback, first, safely lift and support the vehicle, then remove the rear wheels. Disconnect the lower strut bolts and the upper strut mount nuts located inside the trunk. Remove the old strut and install the new one by reversing the process, ensuring all bolts are torqued to the manufacturer's specifications. Finally, reattach the wheels, lower the vehicle, and perform a wheel alignment.
How do you replace front brake rotors on 2005 subaru outback?
To replace the front brake rotors on a 2005 Subaru Outback, start by safely lifting the vehicle and removing the front wheels. Next, remove the caliper by unbolting it and sliding it off the rotor; support it with a bungee cord to avoid straining the brake line. Take off the old rotor, usually by removing any retaining screws, then install the new rotor in place. Finally, reattach the caliper, replace the wheel, and lower the vehicle before testing the brakes.
How do you replace bulb side mirror indicator on Subaru Outback?
To replace the bulb in the side mirror indicator of a Subaru Outback, first, ensure the vehicle is off and safely parked. Gently pry off the mirror cover using a trim tool or flathead screwdriver to avoid damage. Locate the bulb socket, twist it counterclockwise to remove, then replace the old bulb with a new one, ensuring it's securely in place. Finally, reattach the mirror cover and test the indicator to ensure it's functioning correctly.
Why does a 1996 Plymouth breeze start and run until it gets warm then stalls and wont start again until it cools off?
A 1996 Plymouth Breeze that starts and runs until it warms up, but then stalls might have a problem with a temperature sensor. The sensor is telling the computer that the temperature is too high for the engine to operate safely. Check the Electronic Temperature Sensor or the Manifold Pressure Sensor (MAP).
How does a driveway alarm sensor work?
You may want to check out Youtube.com for instructions on your driveway alarm sensor. They have how to's and instructional videos on how to get things complete safely and accurately.
Can you drive your 2000 Toyota Sienna with a bad oxygen sensor?
can you safely drive a 2000 camery with bad sensors
Is a MacBook suitable for a 11 year old?
There is absolutely no problem if it is used judiciously and safely...
Are there any problem of eating strawberry during pregnancy?
No, you can safely eat all fruits and berries.
Where is speed sensor located on 1998 mercury tracer?
A speed sensor on a 1998 Mercury Tracer is located on the transmission housing of the vehicle. It is placed on top in a secure location to safely measure the speed the transaxle spins.
How do you replace 1996 Jaguar XJ6 speed sensor?
To replace the speed sensor on a 1996 Jaguar XJ6, first, ensure the vehicle is safely elevated and secure. Locate the speed sensor, which is typically found on the transmission housing. Disconnect the electrical connector and remove the retaining bolt to take out the old sensor. Install the new sensor by reversing the steps, ensuring it is securely fastened and reconnected.
