0
What else can I help you with?
Is there any adjustment to the crankshaft position sensor when repalcing?
no, there is no adjustment. take old one out and replace with new one. sensor will only fit in one way and will seat itself to proper clearance as you tighten the installation bolt
What is the proper way to replace a bike derailleur cable?
To replace a bike derailleur cable, first shift the chain to the smallest cog. Loosen the cable anchor bolt and remove the old cable. Thread the new cable through the derailleur and housing, then tighten the anchor bolt. Adjust the tension and test the shifting before cutting the excess cable.
How do you adjust a 1998 Nissan 200sx clutch?
I have replaced the the clutch cable on my '95 200sx 1.6L and it was easy. To adjust the cable go to the end of the cable where it conects to the level looking clutch arm in the engine compartment and look at where the clutch cable connects to the lever. Securing the cable on the backside of the lever there is a washer and screw that you can tighten or loosen to engage the clutch without pushing it all the way to the floor or you can adjust the other way to get the opposite affect. After I installed my clutch cable I had to go back about a week later and adjust the clutch (tighten the cable) because it appeared the cable had stretch a little from brand new to broken in condition. Hope this helps...
How do you tighten the fan belt on a 1998 Chrysler Intrepid?
theres no way to tighten it you will have to buy a new belt
How do you change a camshaft sensor on 03 dodge 2500 hemi?
Look behind the alternator. It is held only by one 10mm bolt. Disconnect the cam sensor, then remove the 10mm bolt and pull up on the sensor. It should come right out. Take a rag and clean out the are where the sensor goes in. A quick wipe should do. Push in the new sensor and tighten the 10mm back in place. Connect the harness back, male sure the connector it plug all the way in. Connect the negative cable back to your battery and your done. Took me less than 5 minutes.
How do you adjust the choke on an engine?
(1) Loosen the choke cable at the cable control bracket but do not remove it. (2) Pull cable knob or lever all the way to closed position. (3) Manually close the choke baffle all the way. (4) Tighten the choke cable at the cable control bracket. (5) Ensure choke opens and closes properly by pushing and/or pulling the cable knob or lever.
Change the knock sensor on a 300zx?
1.) Purchase new knock sensor& cable2.) On top of the plenum next to the throttle and ASCD cables there will be a connector that looks exactly like the mating end of your new cable; disconnect the old cable and connect the new one. (The knock sensor is located about 8" below the plenum itself so the only way to get to it is by either removing the plenum and everything attached to it or by pulling the motor and getting at it from the rear [firewall side]). However, you can relocate the sensor on top of the motor as long as it is SOLIDLY mounted to the engine itself. No zip ties or something silly like that.
How do you replace a positive battery cable on a 2000 Chevy blazer and where can you obtain the cable other than the dealer?
You Will Need To Get The Cable From A Dealer. If The Cable Is Burned Into Ect. It Will Need To Be Replaced. If The Cable End Is Bad You Can Try This. Purchase a New Cable End. Yours Probably Has Two Smaller Cables In The Wire Also Besides The Regular One. On The Cable End You Get Also Get One Or Two ( as needed ) Heavy Duty Cable Eyletts That Fit The Bolts That Tighten The Large Cable To The Terminal End. Put The Small Cables On each Side Of The Bolts That Clamp This Down, Tighten It All Down. Should Work OK. I Have Done This Often. If You Do It This Way. You Will Need To Check These Connections Every 3 Months Or So To Be Sure They Are OK.
How do you tighten accelerator cable citroen xsara?
You can adjust it at the pulleyside. There is a little retainer situated in plastickgrooves. Pull the cable tight and place tre retainer so it stays that way. No tools needed, it takes 10 secs.
How do you adjust a choke on a 1994 750 Kawasaki Jet Ski?
Loosen the cable at the carb and hold the choke valve wide open. Then tighten the cable. Check to make sure it closes all the way when you pull the choke lever.
How do you tighten a stripped nut on a battery post?
Best just to remove the nut and replace it with an new one, or grab a pair of pliers and tighten it that way if you absolutely need to.
What is the proper way to replace a rear derailleur cable on a bicycle?
To replace a rear derailleur cable on a bicycle, follow these steps: Shift the gears to the smallest cog on the rear cassette. Loosen the cable anchor bolt on the derailleur and remove the old cable. Thread the new cable through the shifter and housing, then through the derailleur. Pull the cable taut and tighten the anchor bolt. Trim any excess cable and adjust the tension as needed. Test the gears to ensure smooth shifting. Remember to check for proper alignment and consult a professional if needed.
