answersLogoWhite

0

hey, if you mean the the little cylinder thing in your colum, i am working and stuck on that at the moment, you have to pull your steering wheel off, take your blinker etc stuff out, then there are like 5 little holes and in the bottom of one of them there is a screw, you have to take that out and then the cylinder should pull out

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you change ignition switch on 1981 jeep wagoneer?

you must remove the steering wheel and turn signal from column. then you can acces the screw to remove the switch.


How do you remove the ignition switch on a 1989 Jeep?

To remove the ignition switch on a 1989 Jeep, first disconnect the battery to prevent any electrical shorts. Next, remove the steering column cover by unscrewing the screws that hold it in place. Then, locate the ignition switch, which is typically mounted on the steering column; detach the wiring harness and unscrew any mounting bolts to remove the switch. Finally, carefully pull the switch out from the column to complete the process.


What is the method of removing and replacing the ignition switch in a 1984 CJ7 jeep?

To remove and replace the ignition switch in a 1984 Jeep CJ7, first disconnect the battery to ensure safety. Remove the steering column cover by unscrewing the screws, then locate the ignition switch. Detach the wiring harness and unscrew the ignition switch from its mounting. Install the new ignition switch by reversing the steps, ensuring all connections are secure before reconnecting the battery.


How do you remove the ignition switch from the steering column on a jeep grand wagoneer 1986?

To remove the ignition switch from the steering column of a 1986 Jeep Grand Wagoneer, first disconnect the battery to ensure safety. Then, remove the steering column cover by unscrewing the retaining screws. Next, locate the ignition switch, disconnect the electrical connectors, and remove any screws or bolts securing it in place. Finally, pull the ignition switch out from the column to complete the removal.


How do you remove the ignition switch key lock on a 1989 jeep wagoneer?

To remove the ignition switch key lock on a 1989 Jeep Wagoneer, first disconnect the battery to ensure safety. Then, remove the steering column cover to access the ignition switch. Locate the retaining screw or pin on the ignition lock cylinder, turn the key to the "run" position, and press the pin or screw to release the lock cylinder. Finally, pull the key lock out of the ignition switch.


How do you remove the ignition switch key lock on a 1988 Jeep Cherokee?

Remove steering wheel, turn signal (4 screws), and torx holding ignition, reverse to reinstall.


Where is the ignition switch located on a 1988 jeep grand wagoneer?

The ignition switch on a 1988 Jeep Grand Wagoneer is typically located on the steering column, behind the steering wheel. You may need to remove the steering column cover to access it. The switch is usually connected to the ignition key cylinder, allowing power to flow to the vehicle's electrical systems when the key is turned.


How do you remove the ignition switch in a 1999 Jeep Grand Cherokee Laredo?

you take it to the dealer caz you cant do it for sure its incredably complicated


What does an ignition switch do for a 1997 jeep?

It engages and disengages the lock that starts the vehicle. There are 2 parts to the switch. The ignition switch and the lock assembly.


99 Jeep Cherokee Laredo stay running after turn off the ignition switch?

99 jeep Cherokee Laredo stay running after turn off the ignition switch?


How to change ignition switch in 1985 Jeep CJ 7?

To change the ignition switch in a 1985 Jeep CJ-7, first disconnect the negative battery terminal to ensure safety. Remove the steering column trim by taking out the screws, then detach the ignition switch from the steering column by unfastening the retaining screws. Disconnect the wiring harness from the old switch and replace it with the new one, securing it in place. Finally, reassemble the trim, reconnect the battery, and test the ignition switch to ensure it functions correctly.


How do you replace the ignition switch on a 1989 Jeep Waggoner?

you have to remove the steering wheel and the turn signal. this requires special tools that can be purchased or rented cheaply.