answersLogoWhite

0

That depends. Many distributors require that you use feeler gauges and a screwdriver. Some of the GM distributors had a little access door on the side of the distributor cap and you'd use a dwell-tach and an Allen wrench to adjust the points.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What is dwell angle meter?

It was a tool used to accurately set the gap on ignition points. They don't get much use these days.


How do you set Ignition Points Gap on a 50cc malaguti?

To set the ignition points gap on a 50cc Malaguti, first remove the flywheel cover to access the ignition points. Use a feeler gauge to measure the gap between the points, which should typically be set to around 0.35 mm (0.014 inches). Adjust the gap by loosening the screws securing the points and carefully moving them until the correct gap is achieved, then tighten the screws. Always double-check the gap after adjustments to ensure proper ignition timing.


How do you find a tool to set the ignition coil gap on a lawn mower?

you can go to any parts store and buy a feeler gauge for a couple of dollars. use that to set the air gap between the coil and the flywheel. use the oem specs


What is the ignition coil gap on your mcculoch strimmer?

The ignition coil gap for a McCulloch strimmer typically ranges from 0.01 to 0.02 inches (0.25 to 0.5 mm). To set the gap, you can use a feeler gauge or a similar thin tool. It's essential to ensure the gap is correctly set for optimal engine performance and reliable starting. Always refer to the specific model's manual for precise specifications.


What is the gap for a 93 integra?

The gap for a 1993 Acura Integra is 0.44. Use a gapping tool.


Ignition Points and spark plug gap for vw 63 model?

There are kits available which turn your old points distributor into an electronic ignition system, i have converted both my veedubs and it removes all of the guesswork & trouble from your distributor. The kit comes with instructions and is very easy to use, you basically just gut your distributor cap & put in a circuit board & boom, electronic ignition. I will post a link below. Oh, and gap your plugs at .024 inches.


How do you set points on a Mazda B which has points?

To set the points on a Mazda B with a points ignition system, first, remove the distributor cap and rotor to access the points. Rotate the engine to align the timing mark to the correct position (usually at TDC for the number one cylinder). Use a feeler gauge to check the gap between the points; it should typically be around 0.016 inches (0.4 mm). Adjust the gap by loosening the points mounting screws and carefully bending the points until the desired gap is achieved, then retighten the screws and reassemble the distributor.


What is the gap setting on a champion J19lm?

The gap setting on a Champion J19LM spark plug is typically around 0.030 to 0.035 inches (0.76 to 0.89 mm). It's important to check the specifications for your specific engine, as some may require a slightly different gap. Proper gap adjustment ensures optimal ignition and engine performance. Always use a gap tool to measure and adjust the gap accurately before installation.


How do gap set points on dt 125?

To set the gap on a DT 125 spark plug, ensure the engine is cool, remove the old plug, use a gap tool to adjust the gap to manufacturer specifications (usually around 0.6-0.7mm), and then install the new spark plug. Be sure to consult the owner's manual for the specific gap setting recommended for your DT 125 model.


How do you set points gap on a 1977 KZ650?

To set the points gap on a 1977 KZ650, first, remove the left side cover to access the points. Use a feeler gauge to measure the gap while rotating the engine to align the points at their widest opening. The gap should be set to approximately 0.014 inches (0.35 mm). Once adjusted, tighten the points screws and recheck the gap to ensure it remains correct.


Point setting on a Case 300 tractor?

To set the ignition points on a Case 300 tractor, first, ensure the engine is off and cool. Remove the distributor cap to access the points, then rotate the engine until the points are fully open. Use a feeler gauge to measure the gap, which should typically be set to 0.020 inches; adjust the points as necessary. Finally, reassemble the components and double-check the gap before starting the engine.


Did 1974 small block 350 use points ignition?

yes