0
Whats the problem with a 1989 toyota cressida when it runs and then wont start?
I been having trouble with my toyota cressida for a while now. It has stranded me a few times. it runs and then it won;t start. When this happens,I'm turning the ignition and i i hear the door knobs jumping up and down. If I'm lucky the car will start around the 10th or 20th try. If I'm unlucky,I 'll have to call a tow trunk and when it arrives it might start or it will start and i will have to call the tow folks back and cancel the tow.(this is when i' waiting for the tow.) PLEASE HELP ME BEFORE THIS CAR MAKE ME SICKER.!!!!!!!!!! Geraldine Elliott
Get fast answers to your Toyota Cressida questions from experts in the CarGurus automotive community. ... and piston rings on my automatic Cressida but the crank won't turn please help ... have done all thing related to mthis problem but it is not solved what shoould i do? ... Starts right up, runs for 10-15 min then cuts off.
What else can I help you with?
Your 89 Toyota Cressida cranks but does not start what do you do?
Look for spark and fuel 1st then comeback
Where is the cold start valve in the 1989 Toyota Cressida?
The cold start injecter is located in the middle of the intake manifold with the brake master cly. right in the way
Toyota Sienna Won't Start?
There could be several reasons why a Toyota Sienna will not start. the most common problem would be a dead battery.
You put a new fuel pump on 89 Toyota Cressida. it run but the next day you try to crank it up it would not start?
CHECK THE FUSE THATS UNDER THE HOOD
Where can you find the knock sensor in a 1989 Toyota Cressida?
The knock Sensor in a 1989-1992 Toyota cressida is located under the intake manifold, closer and under the cold start injecter. Behind the alternater. i had to use a small mirror to see it, or you can put your hand under and search for it. Also look at this tread forum: http://www.toyotanation.com/forum/showthread.php?t=213375 Thanks
Toyota tacoma auto start system problem?
Try asking a question.
My 92 ex accord dies after a few minutes when you start it then wants to diesel then won't start whats the possible problem?
fuel stop solinoid problem,or air in the lines
How do you disarm a 1989 Toyota Cressida alarm?
use the ignition key to turn to on or to start and the system should reset. I stopped using mine because it would trigger at any time wothout an intrusion
How do you replace bearings on a 1983 Toyota Cressida?
To replace the bearings on a 1983 Toyota Cressida, start by lifting the vehicle and removing the wheel to access the hub assembly. Then, remove the brake components and the hub assembly from the spindle. Carefully extract the old bearings using a bearing puller, clean the hub, and install new bearings with proper lubrication. Finally, reassemble the hub, brakes, and wheel, ensuring everything is tightened to the manufacturer's specifications.
How do you reset alarm so Toyota Cressida will start?
To reset the alarm on a Toyota Cressida, insert the key into the ignition and turn it to the "On" position without starting the engine. Then, press the alarm reset button, usually located on the dashboard or near the steering column, or unlock the driver's door with the key. If the alarm is still active, disconnect the battery for a few minutes to reset the system before reconnecting it. After resetting, try starting the car again.
1983 Toyota Cressida won't start if outside temperature is under 40 degrees F - over 40 degrees no problem?
start by checking choke operation but it sounds like MAP( Manifold Absolute Pressure ) sensor is going bad be sure to disconnect battery before starting project the reconnecting after everything is mounted and hooked back up to prevent shorting out electrical sensor
If my 96 Toyota corolla cranks but wont start what can be the problem?
chances are to start with the fuel filter if that's not it try the fuel pump
