0
There are two timing marks;
* On the bottom crankshaft pulley (alternator belt attached) * On the timing belt pulley (you will need to take off the plastic cover) The timing in a Daewoo is set by the timing belt. If you are replacing the timing belt (if it has broken), you need to
# Check that cylinder one is at the top of it's upward stroke, the timing mark on the crankshaft pulley should be at top dead centre # Remove the valve cover and check that both the inlet and exhaust valve on cylinder one are closed. You should see the cam lobes both pointing up. Looking at a clock, they would be positioned at the 10 and 2 positions. I have found his car to be very frustrating to set the timing when replacing a broken timing belt. No obvious settings, almost need to pull the engine apart and go back to basics to get the timing right.
What else can I help you with?
2000 Daewoo Leganza engine timing diagram?
what is the timing marks on the camshaft what is the timing marks on the camshaft
Where do you set the timing marks on a 2000 daewoo?
the two cams must be at 12oclock and the crank must be at 6oclock
What are the timing marks for a Daewoo cielo 1997?
For a 1997 Daewoo Cielo, the timing marks are typically located on the crankshaft and camshaft pulleys. The crankshaft timing mark is usually a notch or line on the pulley that aligns with a corresponding mark on the engine block. The camshaft timing mark should align with a mark on the cylinder head or timing cover. It's essential to ensure these marks align correctly when setting the timing to maintain engine performance. Always refer to the vehicle's service manual for precise details.
Where are the timing marks on a 2001 1.6 Daewoo nubira dohc?
On a 2001 1.6 Daewoo Nubira DOHC engine, the timing marks are located on the crankshaft pulley and the timing cover. You will find a mark on the crankshaft pulley that aligns with a reference point on the engine block. Additionally, there are marks on the camshaft gears that should align with the timing cover when the engine is at the top dead center (TDC) of the first cylinder. Always ensure the engine is at TDC before making any timing adjustments.
How do you set the timing marks in your Daewoo 2002 lanos?
To set the timing marks on a 2002 Daewoo Lanos, first ensure the engine is at top dead center (TDC) on the compression stroke for cylinder one. Align the timing mark on the crankshaft pulley with the corresponding mark on the timing cover. Next, check that the camshaft timing mark aligns with the mark on the cylinder head. Finally, make sure the timing belt is properly tensioned before reassembling any components.
How do you change a timing belt for a 2000 Daewoo Lanos?
To change the timing belt on a 2000 Daewoo Lanos, first disconnect the battery and remove any components obstructing access to the timing cover, such as the engine mount and accessory belts. Align the timing marks on the crankshaft and camshaft, then remove the old timing belt and tensioner. Install the new timing belt, ensuring it is properly tensioned and aligned with the timing marks, and reassemble all removed components. Finally, reconnect the battery and start the engine to verify everything is functioning correctly.
Diagram of timing belt 2000 Daewoo lanos?
A timing belt diagram for a 2000 Daewoo Lanos typically illustrates the routing of the timing belt around the crankshaft, camshaft, and any tensioners or pulleys. It shows the correct alignment and positioning to ensure proper engine timing. The diagram may also indicate the timing marks on the crankshaft and camshaft to assist with installation. For precise details, it's best to consult a repair manual or technical resource specific to the Daewoo Lanos.
How do you change the Timing Belt in a 1999 Daewoo Laganza?
look at how to set timing mark for 99 daewoo,explained it there
How to set the camshaft timing on a 2001 Daewoo?
Line up the timing marks on both camshaft sprockets so that they face each other. And line up the crankshaft pulley mark with the mark on the engine block.
How do you release timing belt tensioner on daewoo nubira?
How to replace the timing belt for car daewoo nubira1 -step by step
2001 Daewoo nubira timing?
Is your timing belt broken?
A diagram showing the timing marks for a 1999 daewoo matiz?
To set the timing marks on a 1999 Daewoo Matiz, you typically align the crankshaft and camshaft marks. The crankshaft mark is usually at the 12 o'clock position, while the camshaft mark should be aligned with its corresponding mark on the cylinder head. Ensure that the engine is at top dead center (TDC) on the compression stroke for cylinder one. Always refer to the specific service manual for detailed diagrams and specifications for accuracy.
