0
Yes, you can use a 1.5-inch impeller with a 2 HP motor, provided that the motor's specifications align with the system requirements for the impeller. Ensure that the flow rate and head pressure generated by the impeller match the pump's intended application. Additionally, check if the motor can handle the load and any potential increase in operational efficiency. Always consult with a professional or refer to the manufacturer's guidelines to ensure compatibility and optimal performance.
What else can I help you with?
Put a 1 hp impeller on a 2 hp pool motor?
well the motor will like it, it will run cool but the power bill will be high. it will not have the flow of a 2hp impeller
Mercury Marine where is the impeller located on a 7.5 hp motor?
The water pump impeller on a 7.5 hp Mercury outboard, is located on top of the gearcase, and is driven by the driveshaft.
How do you fix a impeller on a Chrysler 25 horsepower outbourd?
This is how to fix the impeller on a Chrysler 25 HP outboard motor. Disconnect the coupling that's on the outside of the leg, flip the housing and twist in impeller.
What parts are needed to change a water impeller on 70 hp Chrysler outboard motor?
18-3085 sierra
How many units consumed 15 hp motor at 3 phase in one hour?
To calculate the energy consumption of a 15 hp motor operating at full load for one hour in a three-phase system, you can use the formula: Energy (kWh) = Power (hp) × 0.746 (kW/hp) × Time (hours). For a 15 hp motor, this equates to 15 × 0.746 × 1 = 11.19 kWh. Therefore, a 15 hp motor would consume approximately 11.19 units of electricity in one hour.
How do you change impeller on Johnson 70 hp outboard?
Changing the impeller on a Johnson 70 hp outboard motor requires pulling the power head and disconnecting the engine. Once this is done, an open end wrench can be used to first loosen the fitting before removal.
How do you remove the impeller on a Mariner 2 hp?
To remove the impeller on a Mariner 2 hp outboard motor, first, ensure the engine is off and cooled down. Disconnect the water intake and remove the lower unit by unbolting it from the midsection. Once the lower unit is detached, locate the impeller housing, remove its screws, and carefully lift out the impeller. Be cautious not to damage the housing or the drive shaft during this process.
How do you change the impeller on a 75 hp force?
To change the impeller on a 75 hp Force outboard motor, first, disconnect the battery and remove the lower unit by unbolting the necessary screws. Next, take off the water pump cover and remove the old impeller, noting its orientation. Install the new impeller in the same position, lubricate it with water pump grease, and reassemble the cover and lower unit. Finally, reconnect the battery and test the motor to ensure proper water flow.
How do you replace water pump impeller on evinrude 40 hp motor?
If the use of a professional to replace the water pump is out of the question, then one should use the manual to locate the correct part on their particular model of the motor. Once it is found, follow the instructions listed in the manual for replacing the part.
Yamaha outboard motor weights?
15 hp
How do you repair a impeller on 7.5 sears outboard motor?
To repair the impeller on a 7.5 HP Sears outboard motor, first, remove the lower unit by unscrewing the bolts that secure it. Once detached, take out the old impeller from the water pump housing, noting its orientation for proper installation of the new one. Clean the housing, install the new impeller, ensuring it fits snugly, and reassemble the lower unit, making sure all bolts are securely tightened. Finally, test the motor in water to confirm proper operation and cooling.
Is a 15 hp gamefisher 2 stroke or 4 stroke?
A 15 hp game fisher motor is most often a 2 stroke engine. However there can also be a 15 hp game fisher motor that is a 4 stroke as well.
