answersLogoWhite

0

There is no way of telling from here. It will be a double breaker, most boxes will have 3 doubles. One for the stove, one for the AC and one for the water heater. Process of elimination should tell you which is for the heater.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How can I turn off an electric water heater?

To turn off an electric water heater, locate the circuit breaker panel in your home and find the breaker labeled for the water heater. Flip the breaker to the "off" position to shut off power to the water heater.


What is the appropriate water heater breaker size according to the water heater breaker size chart?

The appropriate water heater breaker size is determined by the water heater's wattage and voltage, as indicated in the water heater breaker size chart. It is important to match the breaker size to the specifications of the water heater to ensure safe and efficient operation.


What size amp circuit breaker should be used for a hot water tank?

Assuming you are referring to a 240 volt residential hot water heater you will need to install 10/2 NM cable (Romex) with ground from the service panel to the water heater wired to a 30 amp circuit breaker in the service panel. If you cannot see the water heater from the service panel you will need to install a service disconnect at the water heater.


How can I turn off my water heater?

To turn off your water heater, locate the shut-off valve on the cold water supply line leading to the heater. Turn the valve clockwise to shut off the water flow to the heater. Additionally, you can switch off the power to the water heater by flipping the corresponding breaker in your electrical panel.


How is a hot water heater wired from the power source to the heater?

10/3 wire with 30 amp double pole breaker from panel box to water heater.


Where is the thermostat located on a water heater?

The thermostat on a water heater is typically located near the bottom of the tank, behind a panel or cover. It regulates the temperature of the water inside the tank.


How is an electric heater hot water heater turned on?

There is a thermostat inside an accessible panel on the hot water heater. The panel is typically secured by two screws. When the temperature goes below the set level the heater turns on. You'll either see a specific temperature or just an adjustment that says hotter. Some installations have an external timer that might turn off the hot water heater between midnight and 5AM, for example.


How do I go about replacing the thermostat on an electric water heater?

To replace the thermostat on an electric water heater, first turn off the power to the heater at the circuit breaker. Then, remove the access panel and insulation to expose the thermostat. Disconnect the wires from the old thermostat and remove it. Install the new thermostat and reconnect the wires. Replace the insulation and access panel, then turn the power back on and test the water heater.


How do you Reset electronic hot water heater?

You can pull the front panel off the Hot Water tank and there is a red reset button on the electrical that controls the power to the elements. Or, try resetting the breaker on the electrical panel serving the tank.


What are the steps to replace an electric water heater thermostat?

To replace an electric water heater thermostat, follow these steps: Turn off the power to the water heater at the circuit breaker. Remove the access panel to expose the thermostat. Disconnect the wires from the thermostat. Remove the old thermostat and replace it with a new one. Reconnect the wires to the new thermostat. Replace the access panel and turn the power back on. Test the water heater to ensure it is working properly.


How do I check the pilot light on my water heater?

To check the pilot light on your water heater, locate the access panel near the bottom of the unit. Open the panel and look for a small flame burning inside. If the flame is out, follow the manufacturer's instructions to relight it safely.


Do you need to shut off hot water heater when replacing copper pipes in a bathroom?

Yes you need to shut off the Main water valve. Usually found in the basement or outside the house near the meter. Also you need to shut off the Gas valve located at the water heater, or the Breaker located in the breaker box/ fuse panel. Sometimes the water heater will have its own Switch box, located on the power wire