0
What else can I help you with?
What is Boiler feed pump?
Function - It adds the pressure to the feed water before it entyers into boiler feed pump suction Advantage - Ensures high margin NPSH A for boiler feed pump spinning at high rpm (5250Rpm) Drive for booster - Normally @1450 rpm Type of impeller- Mostly preferred Double suction
Why you use boiler in oil refinery?
Use of water in a refinery is makeup for boiler feed. The chief uses of steam are for stripping, steam distillation, and vacuum distillation. The steam comes in contact with the products in these operations, and generally the steam condensate is so highly contaminated that it cannot be reused for boiler feed or for other purposes. Steam is also used for process heating, for pumping, and, in some refineries, for generating electric power
Why is the boiler water circulating pump required for EGB?
I think because it works more like a heat exchanger taking heat from the exhaust gas, rather than a "standard" boiler with a furnace?An EGB needs a pump to circulate the water through the pipes in the exhaust stack, whereas a furnace-heated boiler can use convection to move the fluid through the system..?Might have something to do with lower temperatures in an EGB?
Does condensate return need to go through a flash tank prior to a DA tank for a steam boiler system?
In a steam boiler system, condensate return does not necessarily need to go through a flash tank before entering the Deaerator (DA) tank. However, using a flash tank can be beneficial in recovering some heat and reducing pressure, allowing for more efficient use of the condensate. This process can help minimize the amount of makeup water required and improve overall system efficiency. Ultimately, whether to include a flash tank depends on the specific system design and operational requirements.
What is the name of the chemical you can pump through drip irrigation to clean the lines and drip emitters?
There are a number of things you can use. You can contact the manufacturer of your kind of drip lines and ask them what they recommend. You can pump in a 3% solution of nitric acid, or a 3% solution of common household bleach (sodium hypochlorite). You can also use a solution of 45% hydrogen peroxide mixed with a little vinegar. Whichever solution you use, remember to flush the system completely with clean, clear water. The only real product that removes the blockage in emitters is Line Blaster. lineblaster.com It works quickly, won't hurt the plants, and is economical to use.
How do you make radiator flush solution?
Honestly? No need to bother - just get some CLR and use that.
What are the benefits of a tankless water heater boiler combo for residential use?
A tankless water heater boiler combo for residential use offers benefits such as energy efficiency, space savings, continuous hot water supply, and longer lifespan compared to traditional water heaters.
What are the benefits of a tankless boiler water heater combo system for residential use?
A tankless boiler water heater combo system for residential use offers benefits such as energy efficiency, space savings, continuous hot water supply, and longer lifespan compared to traditional tank water heaters.
Can you run clr through your radiator and engine at the same time to clean out both of them them flush them out good with out damage to either one?
This is not a recommended use for CLR. People have done this and report no adverse result's, but I would not.
How can I effectively use CLR in the toilet tank to remove stubborn stains and mineral deposits?
To effectively use CLR in the toilet tank to remove stubborn stains and mineral deposits, first, turn off the water supply to the toilet. Flush the toilet to empty the tank. Pour CLR directly into the tank and let it sit for at least 10-15 minutes. Scrub the tank with a toilet brush to help loosen the stains and deposits. Finally, turn the water supply back on and flush the toilet to rinse out the CLR. Repeat the process if necessary. Remember to follow the instructions on the CLR bottle and wear gloves and eye protection when handling the product.
Can you use clr in your swampcooler?
yes..but you would have to completely clean the entire unit after you are done and flush it out completely then replace the swamp cooler pads with new ones as CLR is very bad for your health. Using scrub brush is better but harder work.
Can you use clr on ceramic tile?
yes
Can you use CLR in a dishwasher?
It's not recommended to use CLR in a dishwasher as it can leave behind chemical residues that may be harmful if ingested. It's better to use dishwasher-specific cleaners or vinegar for cleaning and descaling your dishwasher.
How do I properly flush a Rheem tankless water heater to maintain its performance and efficiency?
To properly flush a Rheem tankless water heater for maintenance, follow these steps: Turn off the power and gas supply to the unit. Connect a hose to the flush port on the unit. Open hot and cold water valves to allow water to flow through the unit. Use a pump to circulate a descaling solution through the unit for about 45 minutes. Rinse the unit by flushing it with clean water for about 5 minutes. Disconnect the hose and close all valves. Restore power and gas supply to the unit. Regular flushing helps maintain the performance and efficiency of your Rheem tankless water heater.
How to clean a Rheem tankless water heater effectively?
To clean a Rheem tankless water heater effectively, first turn off the power and water supply. Next, remove the cover and use a soft brush to clean the inside of the unit. Use a vinegar solution to descale the heat exchanger and flush it out with water. Finally, replace the cover and restore power and water supply.
Is it OK to use CLR for gun cleaning?
NO! CLP, yes. CLR is a strong acid that is meant for cleaning toilets and sinks. It will corrode a gun.
How do you get rid of scale in the toilet?
Use CLR and a scrub brush
