0
Yes-connect the black wire to the brass terminal and the white wire to the silver terminal.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What form of energy flows through a copper wire connecting the two ends of battery?
Electrical Energy. When a copper wire is connected to two ends of battery, the electrons on the -ve terminal (with excess of electrons) move to +ve terminal (electron deficit terminal) to maintain an equlilbrium, hence the energy created by these movement of 'electrons' is called 'electrical' energy
You have copper and silver speaker wire and the silver has writing on it Which one is positive?
It is traditional to use the copper colored wire as the positive. Of course, the electrons don't care what color the wire is as long as you hook it up the same at both ends!
What happens when a piece copper wire is heated in the outer region of the flame until its red hot?
The copper wire glows red. Once it cools...the copper reacts with the air to produce copper(II) oxide. This is shown by the black tarnish on the copper wire.
A product containing zinc?
A high amount of zinc is in oysters, Some in suntan lotion, and some in copper and brass.
How to clean brass?
Firstly, ensure the item you want to clean, is actually brass. If it isn’t brass, you could end up tarnishing it rather than cleaning. The easiest way to check is to see if a magnet sticks to it. If it’s real brass, the magnet will not stick. If it does stick – do some further investigating and don’t clean it until you’re sure of the metal. Don’t use anything too abrasive on your brass, if you choose to use wire wool, it will need to be a very fine grade. You could end up scratching the surface and causing damage. Try using cotton wool or a soft cleaning cloth to do the dirty work and use another soft cleaning or polishing cloth to get a bit of gleam on your item. visit kernowfurniture.co.uk/blogs/news/how-to-clean-antique-brass for more detail.
How do you wire a wall plug socket?
Wall receptacles are wired in parallel. black to black, white to white, ground to ground.
Where is the position of black wire in electric socket?
In a household circuit, with a "hot" conductor insulated black and a white neutral, the black wire should connect to the center terminal of the socket. The outside part of the socket usually has a brass screw (for the black wire) and a nickel screw (for the white wire).
How do you hook up timing light on a 350 Chevrolet and how can you test your light to know its good?
INSERT PLUG WIRE IN SERIES WITH NO. 1 CYLINDER AND CONNECT BATTERY + TO RED WIRE AND BLACK WIRE TO BATTERY - TERMINAL
How do you bypass the parking brake by grounding wires?
on my older jvc its no problem at all just ground the wire that your radio says to hook up to the ebrake. newer ones and like my pioneer need to have the radio turned on first then ground that wire. trick is --- get a standard universal relay--- like from autozone for your aftermarket driving/fog lights. take the 85 terminal of your relay and hook it to your radios power amplifier wire(usually blue with white stripe), take the 86 terminal and hook it to ground. take the 87 terminal and hook to the same ground, and finally take the 30 terminal and hook it to you radios ebrake wire. simple :-)
How do you hook up in-ceiling speakers?
If you have standard ceiling speakers (with no transformer), you hook up the speaker wiring, Black to the left terminal, and Red to the right terminal. If you have 70V commercial ceiling speakers (with a transformer), you bypass the transformer by either just using the Black and Red wires off of the transformer, or bypass the transformer by hooking the Black wire to the left terminal, and the Red wire to the right terminal. If you have a 70V commercial speaker system (uses transformers on speakers and a 70V PA amplifier), strip the ends of the appropriate wires you are going to hook up to your 70V system. Do not strip the ends of the other wires you aren't going to be using. Hope this helps! Thanks!
What color wire goes to the brass screw on the back of an outlet?
The brass screw is for the hot connection, usually the black wire.; sometimes a red one. The silver colored screw is for the white wire or neutral. If there is a green screw, it's for the ground, usually a bare wire but may also be green.
How to wire a plug with blue brown and Black?
Test the wire with a meter to determine which wire is your hot, which is your neutral, and which is your ground. Those colors are indicative of a 240v circuit normally, so you may have two hots and a ground. Other wise Hot=Black, Neutral=White, and Ground=Green for placement. On your plug, Black/Hot goes to the brass colored terminal. Green/ground goes to the sometimes green terminal that is off by itself usually at the bottom of the receptacle. The neutral goes to the silver terminal.
Does the red battery wire go on the right?
The red battery wire goes on the positive + battery terminal no matter which side it is on. The black wire goes on the negative - terminal.
Where does the wire from the automatic choke hook to on a 1988 b2200 Mazda pickup?
it connects to any positive(hot wire) terminal controlled by key.
What color is the positive wire on the ignition coil for an 87 Porsche 944 turbo?
The positive wire is the 15 terminal and the wire is BK, Black, The 1 terminal is GR, Green
Which terminal does the white wire hook to L1 or L2 on a dayton 5k534 elec motor?
if it is a 240volt motor it does not matter,
What color screw does the black wire attach in a porcelain light fixture?
If there is a brass colored screw and a silver colored screw, the BLACK wire will connect to the brass screw. If you can't see a difference, connect the black wire to whichever screw connects to the CENTER contact of the light fixture.
