This is a 30 amp 125 volt device. The black wire goes on the smallest pin, should be a brass coloured screw, the white on the next in size, should be a silver coloured screw and the ground wire on the pin with the inward hook on it, green coloured screw.
To convert a 3-wire plug to a 2-wire plug, you would typically remove the ground wire from the circuit. This is not recommended for safety reasons as the grounding wire serves to protect against electrical shocks. It is safer to use a 3-to-2 prong adapter if you need to plug a 3-wire device into a 2-wire outlet.
In North America the connections for a 15 amp cap (plug) goes as follows. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw.
Black and Red are hot (2 slots ), white neutral , bare copper (or green) is grounding. The answer is correct, but to carify a bit...Red and black are connected to the brass colored terminals, white to silver and green or bare to the green terminal.
Test the wire with a meter to determine which wire is your hot, which is your neutral, and which is your ground. Those colors are indicative of a 240v circuit normally, so you may have two hots and a ground. Other wise Hot=Black, Neutral=White, and Ground=Green for placement. On your plug, Black/Hot goes to the brass colored terminal. Green/ground goes to the sometimes green terminal that is off by itself usually at the bottom of the receptacle. The neutral goes to the silver terminal.
A polarized plug can only fit together in one direction. This is to prevent reverse polarity in the device you are plugging in.
To properly wire a dryer plug, you need to connect the three wires from the plug to the corresponding terminals on the dryer. The black wire goes to the hot terminal, the white wire goes to the neutral terminal, and the green or bare wire goes to the ground terminal. Make sure to tighten the screws securely and follow the manufacturer's instructions for your specific dryer model.
how to put plug wires on a 1996 Saturn sl
Need to know what engine you have.
With the cover off the plug and looking from the back at the screws the "Live" wire [generally red or brown] goes to the Left - and the "Neutral" wire [generally green] gos to the Right.Another way of putting this would be to say that the red wire must be connected to the prong that goes into the Left hole in the plug outlet in the wall.It is good practice to coil the earth wire in the plug so that, should the lead by tugged hard, it will be the LAST wire to become disconnected from the screws in the plug.AnswerCorrection .... sorry!! With the cover off the plug and looking from the back at the screws the "Live" wire [generally red or brown] goes to the Left - and the "Neutral" wire [generally BLUE] goes to the Right. The Earth [genarally green] goes to the centre prong - assuming it is a 3-pin plug.
http://autorepair.about.com/library/firing_orders/bl-fo-2695.htm which spark plug goes to spark plugs wire set for a Saturn sw 1994
The black wire goes to the brass colored screw and the white wire goes to the silver screw.
That is the rubber boot that is on the end of the spark plug wire that goes onto the spark plug.
A ground wire.
I'm sorry, but WHAT DID YOU DO!?!?!?
hot wire on the timing light goes to pos. side of the battery and the neg. side of timing light goes to ground on the engine someplace and then the plug clip goes on the #1 spark plug wire.
If its a v6 the #6 wire goes on the passenger side closest to the firewall. If its a v8 the #6 wire goes on the passenger side 2nd closest to the firewall.
+ goes to starter solenoid, - goes to distributor side post. center plug wire goes to center plug on distributor.