0
What else can I help you with?
Is turning on a light bulb on a physical or chemical change?
The reason why turning on a light bulb is a physical change is because there is a process of electrical energy being converted into light and heat. You still have the light bulb intact and no new substance is formed.
How do you determine electron affinity?
Measure the equilibrium constant for the reaction of thermal electrons with a species at different temperatures. this has been done with an electron capture detector. another way to measure it is to make a negative ion and shine light on it and measure the energy of the electrons removed by this process Dr.Edward Chen
When one electron moves from the 4th shell to the 2nd shell in hydrogen is energy absorbed or emitted by the atom?
The energy is absorbed by the electrons because work needs to be done on the electrons to raise them to an excited state. Energy is stored in the electrons while they are in their excited state and would emit energy if they returned to their ground state.
Is there a way to draw Bohr diagrams for diatomic molecules?
Bohr diagrams represent the electron shells of individual atoms, so they are not typically used for diatomic molecules, which involve two atoms sharing electrons to form a bond. Lewis structures or molecular orbital diagrams are more commonly used to represent the electron distribution in diatomic molecules.
What color tube is used for the free light chains test?
The free light chains test is typically done using a lavender-top tube. This tube contains EDTA as an anticoagulant and is suitable for plasma collection.
How do you do the light bulb on Habbo?
The light bulb is done by holding alt on your keyboard and pressing the numbers 276.
How many lemons does it take to make a light bulb light?
it takes 3,003,494,560,327,650,836,140,520,347,257,345,803,465,876,324,065,086,237,248 and it still might not get done
How do you replace the heater control light bulb in a Mercedes M Class?
pull the heater control knob off and located behind is a small capless bulb pull out and then push in new bulb replace knob job done
What should be done to light a bulb?
To light a bulb, you need to connect it to a power source such as a battery or electricity supply. The electricity will flow through the bulb's filament, creating light energy and causing the bulb to illuminate. Make sure the connections are secure and the bulb is functioning properly.
How do you fit a new light bulb to a Honda civic clock?
GENTLY PRY OUT THE BOTTOM OF THE CLOCK WITH A SMALL FLAT SCREWDRIVER TAKING CARE NOT TO MARK THE FASCIA, THEN PULL OUT THE CLOCK BEHIND OF WHICH YOU WILL FIND THE BULB CONNECTED, UNPLUG THE BLOWN BULB TAKE IT TO HONDA OF HALFORDS AND BUY A NEW BULB. RECONNECT THE BULB PUSH CLOCK BACK INTO HOUSING.JOB DONE.
How can an electric bulb can be lighted by the energy produced by a single lemon?
Lemons don't usually produce electricity. It would be quite tricky to convert the small amount of energy available in a lemon to electricity. Nor would it be worthwhile; you would probably get a few seconds or minutes of electricity, at most. That is why lemons can produce enough electricity to light a small LED bulb. But a simple experiment can be done by taking a fresh lemon, a small LED bulb and a conducting wire. If you connect the lemon with the wires and the bulb, the bulb will light up for a few mnutes. This happens because lemon which has citric acid helps in electrolysis.
How do you change the rear brake light on a 2002 Toyota Highlander?
The bulb on the highlander is in a plastic holder that screws ? snaps into the hole in the tail light from the inside of the vehicle. On each side just in line with the brake light is a small pannel that just snaps out of and into place. Remove this small panel and behind it you will see 3 bulb holders in a verticle row . Remove the one that is out by turning the bulb holder counter clock wise (to the left) CAUTION : you can drop the bulb holder and it will fall down into the lower finder well and is near impossible to retrieve. It is best to cover the hole in the finder with some tape or ?? . Replace the bulb by pulling the old one out and insert the new bulb. Put the bulb holder back into the hole , align the ears with the proper slots in the tail light and turn to the right until it stops and is in the same position as the others. Replace the small panel and you are done.
What was done before the light bulb was invented?
Oil lamps where used. Candles were also used.
How do you remove a brake light bulb on a F-150?
There are some squares in the back when you drop the tailgate then pull out when it comes out twist the bulb housing and it should come out pull the bulb out and you are done.
How many drummers does it take to screw in a light bulb?
three. one to screw in the bulb and two to talk about how much better neil peart could have done it.
How many cats are in a light bulb?
NONE!!!! to mum! this WAS done by daisy amber *insert last name*
How do you replace the front headlight bulb on a Mitsubishi galant es?
This question did not specify a year, as for the 2000 Galant ES it's fairly simple. You will need a flat head screw driver to remove the light bulb connector from the light bulb. The light bulb is held to the connector with a locking tab, you will need to use the screw driver to free the bulb from the locking tab on connector. Once free you can just pull the light bulb from the rubber housing. Replace with new bulb making sure you do not touch light bulb glass with hands (the grease of your hands sometimes shortens the lifespan of the bulb) snap in connector and you're done.
