0
What else can I help you with?
What is the difference between a stopper and a bung?
A bung is almost always made of plastic/rubber and it could have a hole in it to allow you to insert glass tubes/thermometers etc. These are the ones which you usually use to close off test tubes for short periods of time (i.e, during a reaction etc.) A stopper on the other hand usually refers to a glass stopper which could go in an Erlenmeyer flask for storage or in a separating funnel when it is being inverted and shaken. It is confusing because people often refer to bungs as stoppers and say 'stopper off the test tube' when they mean for you to use a bung. The general rule of thumb is that a bung is usually used in place of a stopper unless you are specifically told to do so!!
What is the purpose of wetting the glass tubing before inserting into a stopper?
Wetting the glass tubing before inserting it into a stopper helps create a better seal by reducing the risk of air pockets. The water acts as a lubricant, making it easier to insert the glass tube into the stopper without damaging either component.
What is the volume of rubber stopper?
The volume of a rubber stopper can vary depending on its size and shape. To find the volume of a rubber stopper, you can use the formula for the volume of a cylinder or sphere, depending on the shape of the stopper. Measure the dimensions of the stopper and plug them into the appropriate formula to calculate the volume.
When was The Crystal Stopper created?
"The Crystal Stopper" was created in 1912 by Maurice Leblanc. It is a detective novel featuring the famous gentleman thief Arsène Lupin.
When a rubber stopper has a mass of 8.46g was immersed in a graduated cylinder containing 25 ml of water the water rose to 30.9 ml Calculate the densityof the rubber stopper?
The volume of the stopper can be calculated by subtracting the initial volume of the water from the final volume. In this case, the volume of the rubber stopper would be 30.9 ml - 25 ml = 5.9 ml. Now, divide the mass of the rubber stopper (8.46 g) by its volume (5.9 ml) to find its density. Density = Mass/Volume, so the density of the rubber stopper would be 8.46g / 5.9ml = 1.43 g/ml.
I have a beautiful glass globe hummingbird feeder that has a rubber stopper. How can I stop the nectar from leaking out of the stopper?
If there is debris on the stopper it might be preventing a good seal. Try removing the rubber stopper and wipe it off to remove any debris that might be on it. Clean out the hole that the stopper goes into as well. This will help ensure a clean seal between the hole and the stopper. Put the stopper back into the hole, making sure it is a tight fit. If it still leaks you may need to buy a new stopper.
What is the hole in the rubber stopper for?
The hole in a rubber stopper is used to allow for the insertion of glass tubing or a thermometer into a container without disrupting the seal created by the stopper. This allows for measurements or additions to be made to the container while maintaining a closed system.
What are the release dates for Single Ladies - 2011 Show-Stopper - 3.5?
Single Ladies - 2011 Show-Stopper - 3.5 was released on: USA: 3 February 2014
Which hole does the rubber stopper go in inside the carb of 1986 Honda fourtrax fourwheeler?
Just sso happens I tore into my carb today and the rubber stopper goes 2nd hole.... outside in .....towards the main jet
What is the device used to bore holes through cork or rubber stopper?
Plug Hole I Think :)
What has one hole and can hold glass tubing?
A rubber stopper with one hole can be used to securely hold glass tubing in place, creating a seal that prevents leaks or spills. The tubing can be inserted through the hole in the stopper, allowing for a tight fit that helps with fluid transfer or containment.
What is the definition of the word bung?
A bung is a stopper for a barrel or bottle.
Does a black hole contain life?
no
Toyota Previa oil light on but full of oil?
Try changing the oil pressure switch. now, where is the oil pressure switch? on the dash next to the trip odometer switch is a rubber stopper or a hole that leads into the dash. push a pen into the hole(remove rubber stopper) and depress the button in there. this is to be done after every oil change.
What is the difference between a stopper and a bung?
A bung is almost always made of plastic/rubber and it could have a hole in it to allow you to insert glass tubes/thermometers etc. These are the ones which you usually use to close off test tubes for short periods of time (i.e, during a reaction etc.) A stopper on the other hand usually refers to a glass stopper which could go in an Erlenmeyer flask for storage or in a separating funnel when it is being inverted and shaken. It is confusing because people often refer to bungs as stoppers and say 'stopper off the test tube' when they mean for you to use a bung. The general rule of thumb is that a bung is usually used in place of a stopper unless you are specifically told to do so!!
Function of cork borer?
Very simple answer: to make a hole in a cork or plastic stopper; the scope is to insert a tube, thermocouple, thermometer, etc.
Why thistle funnel have long vertical tube?
A thistle funnel must be introduced through a stopper hole to deliver a small volume of liquid.
