0
What else can I help you with?
What is difference between datalink layer flow control and transport layer flow control?
The difference between datalink layer flow control and transport layer flow control is the need to keep the different layers of data separate in the flow control option.
What is the main difference between bootp and dhcp?
Dhcp is Direct host configure protocol. This is used to assign IP address Automatically. In a Domain Environment we must need IP Addresses to communicate with one machine to another to access the resources, their are mainly two ways to configure a IP in a system One is static or manual IP and other is Dynamic or Automatic IP. So DHCP help us to configure an IP Address Dynamically.(Network+ Guide to Networking answer)BOOTP relies on a static table to associate IP addresses with MAC addresses, whereas DHCP does not
Which network topology uses a backbone?
Even the smallest LAN technically has a backbone, which could be any of the 4 basic topology types. Any time you need to connect various routers, switches, etc., together you connect them via a backbone cable. A backbone may have its own topology as well,such as a serial bus, parallel, distributed, or collapsed backbone. These topologies do not exactly mirror topologies for a LAN or a WAN.
How do you recover my facebook password?
To recover Facebook password, you need knowledge of computer or contact a professional to help you. I could not recover my password when it was blocked but edwinforex57@gmailcom was the person who helped me to get my Facebook back.
How can we send a message to the whole world?
I NEED TO TELL YOU THAT JESUS IS COMING BACK GET READY PEOPLE DONT THINK ABOUT ETERNITY ITS EITHER HEAVEN OR HELL PICK ONE!!!!
What is the advantages of using switches?
you need switches to help you see. no switches can not help you see.
Two switches are 47 meters apart They need to communicate at 600 Mbps What Ethernet physical layer standard should you use?
i would not wanna do your hw
Does a router need a computer?
only to configure it, after that, no.
What is unmanageable switch?
Unmanageable Switch -Unmanageable Switches are just working on layer 2 switching.these switches are basically counted under dumb switch catagory.By using these kinds of switches we dont have to do anything, not even IP addresses.These switches are Plug n Play devices.Managable Switches -Managable switches comes under smart switch category.These switches performs on layer2 as well as layer3 switching.By using manageable switches we can perform or manage following services over the network infrastructure -DHCP (Dynamic Host Configuration Protocol)VLAN (Virtual LAN)Layer3 Routingetc..These switches are not Plug N Play devices, we need to manage means we need to introduce them to the network first before using it.
How do you configure udp?
You don't need to configure UDP; this is done automatically by the application protocols that use this transport method.
When designing a new network at which layer would you start?
Before talking about layers you need to figure out what kind of network you are trying to build, how servers, workstations, routers, switches and so on.
What the items that need to configure to have a successful connection?
delete
What is the advantage of switching?
you need switches to help you see. no switches can not help you see.
How many switches will i need to set up 8 pc's amd 2 printers?
You will need about 12 switches for your setup of 8pcs and 2 printers. You should have extra switches just in case any of the additional switches fail.
What is the advantage of using switches rather than hubs?
The major benefit of a switch over a hub is the increase in the amount of collision domains. This allows a switched network to benefit from full duplex transmissions, negating the need for CSMA/CD, and doubling the potential throughput for each network segment. Switches typically operate at layer 2 of the OSI model, using destination MAC addresses within the Ethernet frame to intelligently filter or forward packets.
How do you configure a NIC to make a BUS work?
if by BUS you mean Frontside Bus, you dont need to configure anything, it is automatically configured when the computer is made
How can you do the switches in Pokemon Crystal?
You will need to explain what Switches you need help on, since the only ones I can think of are in the Goldenrod Underground during the Rocket Siege
