0
What else can I help you with?
What is the Btu output of an electric heater rated at 15 Kw?
A bit north of 50,000btu/hr
Is remote control an input or output device?
you really have been waiting around 7 years I believe I got the answer I think its a input device I'm sorry you had to wait around 7 years
What unit controls input and output devices?
Every i/o device is controlled by software. Every new device that is installed you must install its device drivers to control the device.
Is a light an input or output device?
A traffic signal is controlled by a control box on the side of the intersection, the control box receives data from electromagnetic sensors under the pavement, and that data is processed by amplifiers inside of the box and the traffic controller makes the appropriate decision on what to do. So to answer the question, the traffic light is a decision made by the traffic controller which is a output.
Where the instruction execution happens?
Different parts of instruction execution happen in different places:Control Unit - fetches, decodes, and distributes decoded instructions to other units.Arithmetic Logic Unit - performs arithmetic and logic instructions on command from Control Unit.Input/Output Unit(s) - performs input/output instructions on command from Control Unit.Memory Unit - stores instructions and data, transfers them to/from other units on command from Control Unit.
Where is the heater control valve on a Chrysler Sebring?
The heater output temperature is regulated by airflow control doors inside the dash, not a water valve.
What is the average wattage output of an electric eel?
The average wattage output of an electric eel is around 600 watts.
Can you run a hot water heater on a 5000 watt output generator?
Yes, you can run a hot water heater on a 5000-watt output generator, but it depends on the wattage requirements of the heater. Most residential electric water heaters require between 3000 to 4500 watts, so a 5000-watt generator should be sufficient for smaller units. However, be mindful of the starting wattage, as some appliances may require additional power to start. Always check the specifications of your hot water heater to ensure compatibility.
What is the wattage output of the Frigidaire FMV157GS microwave?
The wattage output of the Frigidaire FMV157GS 0.5 CuFt Over-The-Range Microwave Oven is 1,000 watts.
Where is the Heater Control Valve on 1997 Chrysler Town and Country?
No such part on a Town and Country. There is a blend air motor under the dash that controls the heater output.
What does high or low voltage do to the capacity of an electric heater?
Yes, voltage effects the output of electric heaters. The wattage output rating of the heater will not be reached due to the lower applied voltage. For example if the heater is 5000 watts at 277 volts, the current is I = W/E 5000/277 = 18 amps. The resistance of the heater is R = W/I (squared) = 5000/18 x 18 (324) = 15.43 ohms. Applying 220 volts on the same heater whose resistance is 15.43 ohms results in this new heater wattage rating. W = E (squared)/R = 220 x 220 (48400)/15.43 = 3137 watts. W = watts, I = amperage, R = resistance in ohms and E = voltage.
What is the kilowatt output of an electric heater that has an ampere draw of 50 amps and a voltage source of 208 volts?
The formula you are looking for is W = A x V. Then divide the wattage figure by 1000 to change watts to kilowatts.
If you have a 300 watt RMS and 1000Watt peak power sub-woofer what rating of an amplifier should one consider using?
an amp with 300 or less rms wattage output and 1000 or less peak wattage output.
Can you boost wattage on 5000watt gas generator?
No, it is not recommended or safe to boost the wattage output of a 5000-watt gas generator. The generator is designed to produce a specific amount of power based on its engine and alternator capacity. Attempting to increase the wattage output can damage the generator and may pose a safety hazard.
Can you run a 277volt heater on 220 volts?
Yes, you can but the wattage output rating of the heater will not be reached due to the lower applied voltage. For example if the heater is 5000 watts at 277 volts, the current is I = W/E 5000/277 = 18 amps. The resistance of the heater is R = W/I (squared) = 5000/18 x 18 (324) = 15.43 ohms. Applying 220 volts on the same heater whose resistance is 15.43 ohms results in this new heater wattage rating. W = E (squared)/R = 220 x 220 (48400)/15.43 = 3137 watts. W = watts, I = amperage, R = resistance in ohms and E = voltage.
How can you get the wattage of a 1x3 solar panel when it is 17 volts output?
u multiply your voltage times max current (amps) and this gives u max wattage.
Is there much difference in the Crunch Power Zone P18004 and the P11002, besides the max wattage?
The wattage and the output provided are the major differences between these two units.
