0
The hole and shaft basis system are pre-defined tables / methods in which you use to find tolerances. If you have a set hole size and wish to find the shaft diameter and tolerance required you would use the hole basis system. If you had a shaft at a set size and needed to find the hole size and tolerance required for it you would use the shaft basis system. If you need any more info on it you could try and Google it or look it up in something like the machinist handbook (probable google it aswell)
What else can I help you with?
Does the term CPU and system unit mean the same thing?
No. The CPU means Central Processing Unit. This is the main processor of the computer. A system unit is the hole unit (or personal computer).
What is a backdoor and rootkit virus?
A hole in the security of a system deliberately left in place by designers or maintainers. The motivation for such holes is not always sinister
List all system call interface?
The system call interface defines all the services of the operating system to the programs. The basis of the different variants of the UNIX operating system is different system call interface. SVID (System V interface definitions ) POSIX standard (IEEE) POSIX 1003.4 is API (Application Program Interface) for the real time systems. www.etherlook.com
What is the most generic software process model which might be used as a basis for managing the development of the virtual reality system?
exploratory development !! we can add new features those are propose by customers
Can a water jet drive propulsion system be used on a sailboat?
Jet drives have been proposed for auxiliary propulsion for sailboats on and off since the 1930s, perhaps earlier. The chief advantage would be minimum drag under sail; no prop, no strut, no shaft. Some racers have even tried a closure flap over the flush inlet hole. This leaves an absolutely smooth hull when under sail. There is, though, no special advantage with regard to engine placement; the engine and drive shaft have to be located to connect to the impeller as directly as possible to minimize power losses. Using a pump that is separate from the engine wastes too much horsepower. Unfortunately, the laws of physics make jet drive extremely inefficient for boats that operate at less than 25 knots, and that includes all sailboats.
What is the difference between hole basis system and shaft basis system?
In a hole basis system, the dimensions of the hole are kept constant while the dimensions of the shaft are varied. In a shaft basis system, the dimensions of the shaft are kept constant while the dimensions of the hole are varied. The choice between the two systems depends on the specific application and the importance of the fit between the shaft and hole.
Why hole basis system is prefered?
Though there is not roach to choose between the two systems, the bole-basis system is mostly used because standard tools such as reamers, drills, broaches and other standard tools are often used to produce holes, and standard plug gages are used to check the actual sizes. On the other hand, shafting can easily be machined to any size desired.
What is the synonym for a vertical hole dug in mine?
A shaft is a hole dug in a mine.
Give the DOF for a shaft in a circular hole?
A shaft in a circular hole has 2 degrees of freedom: rotation around its own axis and translation along the axis of the hole.
Can your brine head fit into your debeer shaft?
Yes. You may need to drill a pilot hole into the shaft to affix the head.
What is another word that means vertical hole dug in a mine?
Shaft.
Which process is used to manufacture shafts and holes?
Double Shaft-Hole Bar
Why is a screw head bigger than the screw shaft?
The screw head is larger to prevent the screw from pulling threw the hole made by the shaft
How can you tell if you need a water pump?
Water pumps fail due to a bad bearing and/or shaft seal. Look at the bottom of the pump. There is a drain hole in the casting below the shaft. If the seal is bad then coolant will be leaking out of this hole.
Why is the hole on your lacrosse shaft bigger than the one on your head and will it work?
it shouldn't be. and no it will not work
Can any lacrosse head fit on a stx scti shaft?
Any head will fit on any shaft. But if you but a head on a shaft that is a different brand than the shaft, you may need to drill a new hole into the shaft. The only exceptions are the STX Crankshaft shafts which need certain heads.
Which blood vessels are associated with a hole in the shaft of long bones?
Diaphysis means the shaft of a long bone. Thus, it would probably be: diaphyseal arteries and veins
