m
A device on a network are gateway, router, bridge, switch, hub, repeater, multilayer switch, protocol converter, bridge router, digital media receiver, proxy, firewall, and network address translator. A computer on a network is called a networking computer. http://en.wikipedia.org/wiki/Computer_networking_device
It is connected by a network cable, switch and a router.
No - a router can connect to a computer, another router, a switch, a hub, a bridge or a modem. If you are connecting to the Internet via DSL or cable company you will need a modem/router to connect to them. You then attach your computer (or computers) to that router. Routers are useful because they make decisions about which way a packet of data goes - this network or this network? If you have one network that doesn't go anywhere (connect to the Internet or another network) a router is of no use to you and a switch generally does wonderfully and is cheaper than a router.
For a small LAN network, a switch is best. To connect two or more LAN networks, a router is required. (2) From Jean Andrews CompTIA A+ sixth edition (page #852): You can use a crossover cable to connect to computers without a switch or hub making it the simplest network of all. For two or more you will need a switch, hub, or router.
SwitchDescription: Network Switch a device that seperates the Broadcast domain of a LAN segment from other segments.
Network+ Guide to Networks answer: Bridge, Switch, Router
You can join LANs and WANs with a Hub, Router, Switch, Gateway, Bridge, Network Interface Card (NIC) and a WAP (Wireless Access Point)..
A device on a network are gateway, router, bridge, switch, hub, repeater, multilayer switch, protocol converter, bridge router, digital media receiver, proxy, firewall, and network address translator. A computer on a network is called a networking computer. http://en.wikipedia.org/wiki/Computer_networking_device
bridge,router,brouter,switch
You need a router. The cable modem connects to the modem's uplink port and the switch can connect to any available port on the router. This wll enable any computers connected to either the router or the switch to access the internet. Through a Wireless Access Point/Gateway/Router. U can connect ur switch w/it's 5 wired pcs to the Router and ur wireless pcs to the router.
Yes, switch as well as hub and router are network devices.
a) A router b) A switch c) All of the above
A gateway is a node (a router) on a computer network that serves as an access point to another network.A Default Gateway is the node on the computer network that is chosen when the IP address does not belong to any other entities in the Routing Table. In homes, the gateway is usually the ISP-provided device that connects the user to the internet, such as a DSL or cable modem. In enterprises, however, the gateway is the node that routes the traffic from a workstation to another network segment. The default gateway is commonly used to be the node connecting the internal networks and the outside network (Internet). In such a situation, the gateway node could act as a proxy server and a firewall. The gateway is also associated with both a router, which uses headers and forwarding tables to determine where packets are sent, and a switch, which provides the actual path for the packet in and out of the gateway. In other words, it is an entry point and an exit point in a network.
Routers are devices that connect to two or more networks in order to forward data packets along those networks. The technical term for this place of convergence is gateway, and in network architecture, the gateway is crucial to maintaining data flow between computers and keeping them connected to the Internet or even an intranet. The most common type of router connection links a cable or DSL modem and two or more home or small office computers.Routers often incorporate hubs and switches into a single device, but these devices are not the same. They are not gateways. Instead, they simply provide links to the network, and they deal with data frames, as opposed to data packets. Hubs cannot determine destination, so they must broadcast every frame to every port, which creates redundant traffic. Switches record MAC addresses, so unlike a hub, it sends the frame directly to its destination port.A network bridge, or simply a bridge, is like a switch. In fact, the difference between a switch and bridge is often that the switch has many more ports. That simplicity, however, is an advantage in scenarios where the complexity is unnecessary. Cost is lower, and performance may be higher. The most common use for a network bridge is to connect network segments, particularly segments that require network communication but do so only infrequently.Bridge ModeMost modern routers have a bridge or switch mode, which essentially forces the router to stop behaving like a gateway. This diminished behavior is useful in certain networking scenarios, such as daisy chaining routers. Rather than potentially cause conflicts, one router does the necessary gateway work while the others serve a support role. Although useful when the need arises, this is not cost effective. Purchase a bridge/switch if you know you need it.Turning a Modeless Router into a BridgeIn home environments, we often use bridges to connect wired devices to our wireless networks. So what do you do if your old router has no switch/bridge mode? For best performance, you cannot simply connect it. Instead, you need to replace the unit's firmware so that it behaves like a bridge or switch. Some router manufacturers provide this firmware but many do not. In the case yours does not, you can use a freely available firmware such as DD-WRT.
A switch cannot function as a router. But you can plug a switch in to one of the ports on the router if you need additional ports.
Provided the manufacturers are compatible you can connect your network swithc to your router.
A gateway is a node (a router) on a computer network that serves as an access point to another network.A Default Gateway is the node on the computer network that is chosen when the IP address does not belong to any other entities in the Routing Table. In homes, the gateway is usually the ISP-provided device that connects the user to the internet, such as a DSL or cable modem. In enterprises, however, the gateway is the node that routes the traffic from a workstation to another network segment. The default gateway is commonly used to be the node connecting the internal networks and the outside network (Internet). In such a situation, the gateway node could act as a proxy server and a firewall. The gateway is also associated with both a router, which uses headers and forwarding tables to determine where packets are sent, and a switch, which provides the actual path for the packet in and out of the gateway. In other words, it is an entry point and an exit point in a network.