0
When the config tab is locked on an end device, you can typically access the device's configuration through a console connection or a terminal emulator using command-line interface (CLI) commands. Alternatively, some devices allow for configuration via a web interface or management software. If administrative access is required, you may need to reset the device to factory settings or authenticate with appropriate credentials to unlock the config tab. Always ensure you have proper authorization to make changes to the device.
What else can I help you with?
Which password would allow a user to establish a Telnet session with a Cisco device?
On user exec mode type enable.When you are on the privilege mode type configure terminal.Upon reaching global config mode you have to type line vty 0 4.Inside the vty line mode type password Please see below example:Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#line vty 0 4Router(config-line)#password secretRouter(config-line)#exitRouter(config)#exit
Why would you want to disable CDP on an interface or globally?
You don't want to allow adjacent devices to gain information about this router for security reasons.SolutionYou can disable CDP on a single interface by using the command no cdp enable interface configuration command: Router1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router1(config)#cdp runRouter1(config)#interface FastEthernet0/0 Router1(config-if)#no cdp enableRouter1(config-if)#end Router1#And you can disable all CDP on the router with the global configuration command, no cdp run: Router1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router1(config)#no cdp runRouter1(config)#end Router1#
Which command enables rip on a router?
A(config)# router rip A(config-router)# passive-interface S0/0 B(config)# router rip B(config-router)# network 192.168.25.48 B(config-router)# network 192.168.25.64 A(config)# router rip A(config-router)# no network 192.168.25.32 B(config)# router rip B(config-router)# passive-interface S0/0 A(config)# no router rip
What is the the sequence of commands for setting the enable secret to Chile?
To set the enable secret to "Chile" on a Cisco device, enter the following commands in configuration mode: Access the global configuration mode by typing configure terminal. Set the enable secret by typing enable secret Chile. Exit the configuration mode by typing exit or end. Make sure to save the configuration with write memory or copy running-config startup-config if necessary.
What is the command used to get into global configuration mode on a cisco router?
On user exec mode type enable. When inside the privilege mode type configure terminal. You will then be sitting into global config after this. Please see below example: Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Which of the following commands sets the secret password to Cisco?
In the global configuration mode, type enable secret See below example:Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#enable secret passwordRouter(config)#exitRouter#
Is a server an end device or an intermediary device?
A server Is an end device. A server, is innately is either a source or destination device, which is, by definition an end device
At the end of glycolysis about 90 percent of the chemical energy is locked in the bonds of what molecule?
At the end of glycolysis, about 90 percent of the chemical energy is locked in the bonds of pyruvate.
Which device type best describes a function of a wireless device?
an end device
What is the purpose of the plug end in an electrical device?
The purpose of the plug end in an electrical device is to connect the device to a power source, allowing electricity to flow into the device and power its functions.
What is Used to end a locked up program?
task manager
How can I establish a USB MIDI connection between my devices?
To establish a USB MIDI connection between your devices, you will need a USB MIDI interface cable. Connect one end of the cable to the USB port on your computer and the other end to the MIDI port on your MIDI device. Install any necessary drivers or software, then configure your devices to recognize the MIDI connection.
