answersLogoWhite

0

I can only assume that you are attempting to connect 480VAC coil from a elevator to a fire system in order to shunt the elevator. In order to do this you will need a shunt trip breaker rated for this use.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you connect the coil on the Mazda or ford 323 1995?

To connect the ignition coil on a 1995 Mazda or Ford 323, first ensure the vehicle is turned off and the battery is disconnected for safety. Locate the ignition coil, which is typically mounted near the engine. Connect the positive terminal of the coil to the wiring harness, ensuring a secure fit, and then connect the negative terminal to the ignition system. Finally, reconnect the battery and check for proper operation.


How do you connect energy meter in circuit?

pressure coil or voltage coil across the supply and the current coil in series.


Where is the EDIS on a 93 Ranger 2.3?

That's the 2 coil packs where one end of the spark plug wires connect ( Electronic Distributorless Ignition System )


Can you connect pressure coil instead of current coil in watt meter to measure power?

You have to connect both coils to measure power: the current coil in series with the load, and the voltage ('pressure') coil in parallel with the supply. And you have to observe the wattmeter's polarity markings if you don't want it to read downscale (backwards)!


How do you wire the ignition coil to the distributor on a 1966 Chevelle?

To wire the ignition coil to the distributor on a 1966 Chevelle, connect the positive terminal of the ignition coil (marked as "B" or "+") to the positive side of the battery or ignition switch. Then, connect the negative terminal of the ignition coil (marked as "C" or "-") to the distributor's primary wire, which runs to the ignition points. Ensure that all connections are secure and insulated to prevent short circuits. Finally, check that the ignition system is properly grounded for optimal performance.


How do you connect a diode across a ac coil?

You mean ac coil, the secondary coil, of a transformer? Then for the purpose of rectification, that is , for changing ac into dc, a diode is connected in series with the secondary coil of the transformer.


What is a coil pack for a 97 dodge neon?

Mounted on your valve cover is a box where your spark plug wires connect. This is the coil pack


How do you connect domestic coil on keystoker k6 boiler to existing hot water tank system?

Connect the domestic coil thru a tempering valve to the hot water pipes in your house and turn off the valves to your old hot water heater. You should include a shutoff valve so you can revert to the hot water heater when you have your coal boiler shut down.


What is the difference between a 3.9 and a 4.0 coil pack on a 2003 Lincoln LS?

The 3.9 liter V8 engine in a 2003 Lincoln LS has the Coil On Plug ( C.O.P. ) ignition system with ( 8 ) individual coils The Ford 4.0 liter V6 has ( 1 ) coil pack that has ( 6 towers ) where the spark plug wires connect


how does an external resistor connect to ignition coil?

An external resistor connects to an ignition coil by being wired in series with the coil's primary winding. This resistor limits the current flowing to the coil, helping to prevent overheating and ensuring proper voltage levels for the ignition system. Typically, it is connected to the positive terminal of the coil and the ignition switch, while the other terminal of the coil connects to ground. This setup is common in older ignition systems to manage the power output effectively.


How do you change internal coil to external coil with control module in Mazda mx-3?

To change the internal coil to an external coil in a Mazda MX-3, you need to first remove the existing internal coil and disconnect the wiring. Install the external coil in a suitable location, ensuring it is securely mounted. Then, connect the new coil to the ignition control module, following the appropriate wiring diagrams to ensure proper connections. Finally, verify that all connections are secure and test the ignition system to ensure proper functionality.


How do you connect a 22r distributor and coil?

Distributor has a center conductor that links to the coil via a wire the same size as your spark plug wires..