Yes, if the flooring is level, uncracked, and has no loose pieces. You will need to strip the surface of the slate to ensure no residue remains that would not allow the mortar to bond.
Slate is a fine-grained, foliated, homogeneous metamorphic rock which is derived from an original shell type sedimentary rocks composed of a clay of volcanic ashes. It could contain quartz, calcite, dolomite, feldspar, pyrite, rutile, graphite, chlorite, and other minerals.
Oh, dude, floor tiles are usually made from rocks like marble, granite, limestone, and travertine. They're basically fancy rocks that people walk all over. So, next time you're strolling across your marble floor, just remember you're basically walking on a fancy boulder.
Shale can be turned into slate through metamorphism, which involves applying heat and pressure to the shale over time. This process causes the minerals in the shale to recrystallize and align, creating the distinct layers, smooth texture, and foliation characteristic of slate.
Slate is formed from shale, which is a fine-grained sedimentary rock composed of clay and silt particles. Over time, high pressure and heat cause the shale to recrystallize into slate, a metamorphic rock known for its ability to easily split into thin sheets.
Slate clips - Qualcraft is the manufacturer of a slate roof clip commonly used to secure a slate roof. The tongue part is hooked to a roof nail (at least a 16 penny nail, 3 1/2″) and then 2 more are used to secure the bracket. There is a lot of weight hanging from these brackets, so securing them properly is essential. Make sure the lock is secure! These brackets allow a 2″x 10″ shelf to be slid between the brackets and gain access to the roof. Always secure the shelf to the bracket with a nail or screw. Video made available by Joe Jenkins and the Slate Roof Warehouse. The SLATOR (Secure Ladder And Tie Off Responsibly) is a newer product that allows roofers to easily and safely access slate roofs. Unlike a ridge hook, the SLATOR can be used on hipped roofs and other places where the ridge is not accessible. The SLATOR is screwed into the rafters with approved fasteners, and then a ladder is securely clamped into the SLATOR. The first SLATOR is usually installed at the eaves. The SLATOR has a built-in OSHA-compliant anchor point for fall protection. This process can be repeated on the roof as necessary to reach repair areas or to install fall protection for all workers. Slate Repair StortzStortz slate ripper - Once you have access to the roof, it's time to remove the broken slates. The slate ripper is the best way to accomplish this. A thin, strong blade are the desired characteristics. If the blade is too thick, it can break neighboring slates. The Stortz ripper is forged in one piece and has higher strength than a welded ripper. The curvature is also important, as a stiff blade can do more harm than good. Once the pliers are pushed under the broken slate, the ears hook on to the nails, and hitting the handle of the pliers back with the hammer removes the nails, allowing the slate to be removed. Hook - When a piece of slate has been removed, the most common way to replace it is with a slate hook. A hook is connected to the underlying layer and then hammered into the lining. A new piece is then inserted into the slate and slid onto the hook. The materials available are copper and stainless steel. Stainless hooks are stronger and better suited to harder coverings, but the aesthetics of copper may be appealing to some. Another method of attaching replacement slates is the nail and batten method. Most prefer the slate hook method because nails can damage other slates and slates can fall out or rust. A slate hook also costs much less than a copper slab. Restoration hammer - A restoration hammer and a slate hammer are two different hammers. A slate hammer is used for cutting, nailing and hammering nails. It is useful when working in valleys, in places where cutting is required, and when laying new layers of slate. For repairs, it is important to have a restoration hammer with you. A heavier hammer is needed to hit the ripper when removing slate. You should NOT use your precious slate hammer. It is used for hitting nails and attaching slate hooks. Ridge hooksNake hooks - If the roof has a ridge and it can be reached with a portable ladder, the ridge hook is the fastest way to reach a repair site. Once a ridge hook is attached to a ladder, the ladder is rolled onto the roof and then flipped over. The device "hooks" over the ridge and uses gravity to hold the ladder in place while the user climbs the ladder. Sometimes a piece of slate does not fit exactly into the dimensions of a repair. A slate cutter is lightweight, portable and cuts slate to the right size, making it essential for repair work. A cutter can also be used to make concave and convex cuts for decorative work. The punch can also be used for nailing.
No, slate requires a mud bed or cement board subfloor.
Yes, but it would have to be floating engineered wood.
To install vinyl flooring over tile, you will need to thoroughly clean and smooth the tile surface, apply a self-leveling compound if needed, and then use a vinyl flooring adhesive to secure the vinyl tiles or planks in place. It is important to follow the manufacturer's instructions and ensure that the tile surface is suitable for vinyl installation.
To install tile over vinyl flooring, first clean and prepare the vinyl surface. Then, apply a layer of thin-set mortar and lay the tiles in the desired pattern. Allow the mortar to dry completely before grouting the tiles. Finally, seal the grout to finish the installation.
The best basement flooring option to install over concrete is luxury vinyl plank (LVP) flooring. It is durable, moisture-resistant, and easy to install.
Yes, it is possible to install linoleum over existing linoleum flooring as long as the existing flooring is in good condition and properly prepared.
You can lay tiles again but make sure you buy proper mortar. You can install any kind of floating floor such as laminate, engineering wood, interlocking vinyl tile. Your main concern should be structural integrity of existing floor, if its not falling you can do pretty much anything
Yes, you can install vinyl flooring over tile as long as the tile is in good condition and the surface is properly prepared.
Yes, you can install vinyl flooring over existing vinyl flooring as long as the existing flooring is in good condition and properly prepared. It is important to follow the manufacturer's guidelines for installation to ensure a successful outcome.
Yes, you can install peel and stick flooring over tile as long as the tile is clean, smooth, and in good condition.
Yes, you can install vinyl flooring over existing tile as long as the tile is in good condition and the surface is smooth and clean.
Yes, it is possible to install granite tiles over existing ceramic tile flooring, but it requires proper preparation and consideration. The ceramic tile surface should be thoroughly cleaned, and any loose or damaged tiles should be repaired or replaced. The surface should be level and free from any residue or debris. Applying a bonding agent or primer can improve adhesion. It's important to note that adding granite tiles will increase the height of the floor, so door clearances and transitions may need adjustment. Consulting with a professional installer or contractor can ensure proper installation and address any specific requirements or challenges.