0
What else can I help you with?
Formula for aqueous hydrogen silicate?
Adding one hydrogen to silicate will give you [HSiO3]-1. In order to get an aqueous form of hydrogen silicate, two hydrogens must be added, giving H2SiO3.
What colored coating is formed on adding zinc granules to freshly prepared ferrous sulphate solution?
A red-brown colored coating is formed on adding zinc granules to freshly prepared ferrous sulphate solution. This is due to the oxidation of ferrous ions in the solution to ferric ions, which results in the formation of ferric oxide/hydroxide on the surface of the zinc granules.
What is the relative formula mass of iron sulphate?
The relative formula mass of iron sulfate is 151.85 g/mol. It is calculated by adding the atomic masses of all the elements in the compound, which are iron (Fe), sulfur (S), and oxygen (O).
Is calcium silicate safe to ingest?
Calcium carbonate is the least useable form of calcium found in nature. Carbonate is such a bad chelator it cannot be considered as such, it is simply an anion. Chelated calcium is what the body needs. calcium orotate, calcium citrate, and the like. Ionized calcium is used by nanobacteria to build calcium plaque, so if you meet a person with atherosclerosis who wants to die sooner, give that person some coral calcium.
How do you separate lead sulphate and lead chloride?
Lead chloride dissolves in hot water, whereas lead sulphate does not. Mix the sample with hot water and filter off the lead sulphate, then evaporate the water and dry the solid left behind to recover the lead chloride.
What is the purpose of adding dilute hydrogen sulphate while electrolysis of water?
You add electrolytes (i.e. hydrogen sulphate) to increase the electrical conductivity of your solution. This speeds up the charge transport and thus the reaction speed at the electrodes.
How is copper released from a copper sulphate solution?
Copper can be released from a copper sulfate solution by electrolysis or by adding a more reactive metal, such as iron or magnesium, which will displace the copper in a single replacement reaction. Another method is to heat the solution to evaporate the water, leaving behind solid copper sulfate which can then be reduced to obtain copper metal.
How would you separate lead sulphate from a mixture of lead sulphate and lead chloride?
Lead sulphate is insoluble in water, while lead chloride is soluble. You can separate the two compounds by adding water to the mixture, which will dissolve the lead chloride and leave the lead sulphate as a solid precipitate. You can then filter out the solid lead sulphate to separate it from the soluble lead chloride.
How can you get zinc chloride by adding zinc sulphate into sodium chloride?
The reaction is not possible.
How can you improve the yield of barium sulphate in a gravimetric analysis?
To improve the yield of barium sulphate in a gravimetric analysis, you can ensure complete precipitation by adding the appropriate amount of precipitating agent (sulfuric acid or barium chloride) slowly with stirring. Additionally, allowing the precipitate to settle and then filtering it using a fine filter paper can help to remove impurities and increase the yield. Washing the precipitate with the solvent used in the precipitation step can also improve the purity of the barium sulphate.
Did you ruin the engine by adding low silicate coolant in your 1999 Chevy Camaro?
What does your owner's manual say to use? If low silicate is not listed then drain and refill with the proper coolant.
When adding aluminum sulphate to swimming pool should the filter be running?
Add the aluminum sulphate to the pool. Run the filter for two hours. Wait overnight to vacuum the bottom of the pool.
Formula for aqueous hydrogen silicate?
Adding one hydrogen to silicate will give you [HSiO3]-1. In order to get an aqueous form of hydrogen silicate, two hydrogens must be added, giving H2SiO3.
What produces white precipitation when reacted with aqueous barium nitrate?
Adding a solution of Sodium Sulphate to aqueous Barium Nitrate will produce a white precipitate of Barium Sulphate with Sodium Nitrate remaining in solution.
What is the purpose of adding sugar to cookie dough?
The purpose is to make it sweet.
How do you determine the sulphate?
Sulphate ions can be determined using methods such as gravimetric analysis, titration with barium chloride, or ion chromatography. In gravimetric analysis, sulphate ions are precipitated as barium sulphate and weighed. Titration with barium chloride involves adding a known volume of barium chloride solution to the sample containing sulphate ions, and the excess barium chloride is back-titrated with a standard solution of a titrant such as potassium chromate. In ion chromatography, separation and quantification of sulphate ions are done using a chromatographic column with specific properties.
What are the purposes of adding so?
There are not much purpose of that.
