It really depends on what you mean by 'measure' -that is, what quantity you wish to measure: voltage, current, power, or energy. It also depends on whether the load being supplied is balanced (i.e. having identical phases) or unbalanced. It also depends on whether you wish (in the case of voltage and current) whether you wish to measure line quantities or phase quantities. So, as you can see, you really require quite a complex answer!
The three energised ('hot') conductors that connect a three-phase supply to its load are called 'lines' and the fourth conductor (if present) is called a 'neutral'. 'Phases' are connected either between lines, or between individual lines and the neutral, depending on whether the loads are connected in delta (three-wire systems) or star(four-wire systems).
(Beware that some writers confuse 'lines' and 'phases', calling line conductors 'phase' conductors; you must always use the correct terminology!)
As the line voltages (voltage between lines) are determined by the supply, they are always equal -so to measure the line voltage, only one voltmeter is needed, and it can be connected between any two lines. For a balanced load, all three line currents are equal, so only one ammeter is needed, and it can be connected in series with any one of the individual lines. For an unbalanced load, the line currents are different, so you need to connect three, separate, ammeters, each in series with a line.
To measure power for a balanced, or unbalanced, load, you can use one less wattmeter than there are conductors supplying the load. So for a three-wire system, you can use two wattmeters but, for a four-wire system, you must use three wattmeters. You will need to check out the internet to find a schematic diagram for these connections: search for 'three-wattmeter method', and 'two-wattmeter method'.
Energy meters follow the same connections as the wattmeter methods, but usually comprise a single instrument, rather than individual instruments so, again, you'll need to do an internet search for their wiring diagrams.
Can u imagine a merrygoround with so many kids on it that three kids can hardly turn it? now imagine that same merrygoround with only two kids trying to turn it. Same thing with one line missing. it will sit there and burn until a breaker goes or the other kids burn out.If you have a motor running it will run until it is stopped but it wont start again.:motors;called single phasing,, the other 2 phases ampers increase and trip the motor overloads.. or blow fuses
When three phase supply is given to the three phase stator winding of the induction motor,a rotating magnetic field is developed around the stator which rotates at synchronous speed.This rotating magnetic field passes through the air gap and cuts the rotor conductors which were stationary.Due to the relative speed between the stationary rotor conductors and the rotating magnetic field,an emf is induced in the rotor conductors.As the rotor conductors are short circuited, current starts flowing through it.And as these current carrying rotor conductors are placed in the magnetic field produced by the stator, they experiences a mechanical force i.e. torque which moves the rotor in the same direction as that of the rotating magnetic field. the induction motor can't run at the synchronous speed because at synchronous speed the induction motor can not develop any torque to move the rotor from its stationary position.
Hilda Taba's curriculum development model, introduced in 1962, focuses on a systematic approach that involves three main stages: diagnosis, design, and evaluation. In the diagnosis phase, educators gather data to understand the learners' needs and current knowledge. The design phase involves creating learning experiences and activities based on the diagnosis. Lastly, the evaluation phase assesses the effectiveness of the curriculum in achieving its goals and objectives, leading to revisions and improvements as needed.
Validity: Ensuring that the evaluation tool accurately measures what it is intended to measure. Reliability: Consistency in the results obtained when the evaluation tool is used multiple times. Fairness: Ensuring that the evaluation tool provides an equal and unbiased assessment for all participants.
No because when their angle measure are equal then they can be acute which only mean that the angle degrees would be 90 and so that isn't acute but only a right angle
You don't. A three phase motor will not start unless it is connected to a three phase supply.
If you want a five-phase supply you need to start with a three-phase supply and a transformer that has 15 symmetrical cores. But why would one need a five-phase supply . . three is enough.
The cheapest service to construct is a single phase service. A three phase service requires more equipment and materials to complete a service.
With no three phase power supply you can't use a three phase motor of any kind at all!
yes
How much current equipments are drawing from three phases (combined or individual) is called three phase load and how much supply we are getting from source is called three phase supply. Ex. In INDIA single phase supply is 220 volt ac with neutral. So in three phase supply all RYB phases should be 220 volts ac with neutral individually. If we calculate with phase to phase than it shoulb be 415 volts ac.
No.
No, a single-phase supply cannot be directly used in a three-phase system. The voltages and phases are different, so additional equipment such as a phase converter or transformer would be needed to convert the single-phase supply to match the requirements of the three-phase system.
By using a three-phase rectifier.
1. 3 phase is more efficient for electric motors. 2. Electric motors start easier with 3 phase. 3. Less current draw 4. Less heat is produced that is waste.
It must be a three phase supply service to run a three phase motor.
Any where that a three phase supply distribution is needed to operate three phase equipment.