answersLogoWhite

0

Google. "Unbrako" They make pressure plugs and describe what they are. In short. A pressure plug is often used in Hydraulics to seal off 5000 psi oil. the taper ensures the formation of a tight seal in the thread.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Educational Theory

What is an explaination of briefly porous plug experiment?

it is an experiment where the gases are either cooled or heated when they are subjected to throttle expansion , i.e when they pass from a region of high pressure to a region of low pressure at some constant temperature. the cooling or heating of a gas depends upon the constant temperature.


Function of manometer?

The function of a manometer is to measure the pressure of a fluid, usually a gas or a liquid. It consists of a sealed tube filled with the fluid being measured, with one end open to the environment and the other end connected to the source of pressure. As the pressure changes, the fluid in the manometer rises or falls, allowing the measurement of the pressure.


What is high pressure compressor in turbine engine?

In an axial flow turbo fan engine there are two compressors. The first compressor is the low pressure compressor or it can also be referred to as the fan and is the first rotating assembly in the engine located aft of the engine inlet. The second rotating assembly located aft of the low pressure compressor or fan is the high pressure compressor. The basic difference between the low and high pressure assemblies is the amount of air pressure they generate. Low pressure compressors usually have a small number of stages and fewer and larger blades. Whereas the high pressure section has more stages and smaller blades. As the air passes through each stage of the compressors it is squeezed thus the pressure and temperature increase. When the air flow exits the high pressure compressor it is at its highest temperature and pressure generated by the cold section (compressor section) of the engine. Hot section/combustion section is another matter. Keep in mind that there are numerous turbo fan/turbine engines and each one probably will be configured differently as far as the number of stages and blades in each compressor section.


What is the pressure of a 100 foot height pipe?

The pressure of a pipe at a 100-foot height is dependent on the fluid inside the pipe and the acceleration due to gravity. The pressure can be calculated using the equation P = ρgh, where P is the pressure, ρ is the fluid density, g is the acceleration due to gravity, and h is the height of the column of fluid.


How does homework cause stress and pressure?

Homework can cause stress and pressure by creating time constraints, increasing workload, and requiring students to balance multiple responsibilities. The fear of not completing homework or doing it poorly can also intensify stress and pressure, leading to feelings of anxiety and overwhelm.

Related Questions

What is the difference a plug valve and a needle valve?

A plug valve controls flow using a cylindrical or conically tapered plug, providing quick open and close operation. A needle valve controls flow with a long, tapered needle that fits into a seat, allowing for precise flow regulation in applications requiring fine adjustments.


Is the gasket on a spark plug the same thing as the washer that comes with it?

That is the gasket. XXXXXXXXXXXXXXXXXXX A gasket or washer is NOT required on a tapered seat spark plug.


What is the correct spark plug for 1965 Chevy 350 with HEI?

A 1965 Chevy didn't come with a 350 and HEI. Best guess would be to use a spark plug for a vehicle that came with that engine and ignition. If the engine has iron heads, it probably needs a tapered seat plug. A good starting point would be R44TS or R44T(with washer) if not a tapered seat plug. For plug gap, try about .045".


Why the rotameter is tapered?

to create annular area so that the diff. pressure can be kept constant.


What is the spark plug type for a 1968 ford 390?

A 1968 Ford Galaxie 500 with a 390 engine should use a spark plug such as an E3 brand spark plug. This plug should have a tapered seat with 18mm threads.


What are the different type of plug valve?

Plug valves are valves with cylindrical or conically-tapered "plugs" which can be rotated inside the valve body to control flow through the valve. There are two types of plug valves - one has a port through a cylindrical plug and the other is the eccentric plug valve.


What are the different types of valve?

Plug valves are valves with cylindrical or conically-tapered "plugs" which can be rotated inside the valve body to control flow through the valve. There are two types of plug valves - one has a port through a cylindrical plug and the other is the eccentric plug valve.


How does a rupture disk differ from a fusible plug?

A rupture disk (disc) is a pressure relief device that reliefs pressure when the pressure inside the protected equipment exceeds the set pressure. A fusible plug reliefs pressure when the plug is weakened due to high temperature.


What happens when a auto differential plug is tightened too tightly?

There will be to much compression in the cylinder and your car wont start! If that differential plug is the tapered pipe thread type, you could crack the case by overtightening.


What is Tapered stick?

A tapered stick will be thicker at one end.


When was Tapered cavesnail created?

Tapered cavesnail was created in 1976.


What does tapered feathers mean?

Tapered feathers are feathers that narrow to a point, or taper.