0
A 120 V power supply connected to a 30 ohm resistor will produce how many amps of current?
Wiki User
∙ 12y ago
A 120V power supply connected to a 30 Ohm resistor will produce 120/30 or 4 amps of current.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
When an inductor and resistor are connected in parallel by how many degrees is the current flow through the resistor out of phase with the current flow through the inductor?
When a resistor and an inductor are both connected to an AC supply, the current in the resistor is in phase with the voltage, while the current in the inductor is a quarter-cycle (90 degrees) behind. Supposing they both draw 1 amp on a 12-volt AC supply. The resistor will dissipate 12 watts, while the inductor will dissipate no power. Any power that enters the inductor comes back to the generator in a later part of the cycle. But the current drawn from the supply is 1.414 amps, so this would be a load with a power factor of 0.707.
What is the function of rheostat in this experiment?
A rheostat is the name given to a variable resistor when it is used to control current. When a variable resistor is used to control voltage, we call it a potentiometer.A rheostat is connected in series with a load, and two of its three terminals are used. A potentiometer is connected in parallel with the supply, and each of its three terminals are used.So the terms 'rheostat' and 'potentiometer' are the names given to describe the function of a variable resistor, not the variable resistor itself.
What does a inductor do when connected across ac supply?
opposes changes in current
What is the voltage drop across a 12 ohm resistor with a source of 24 volts?
If there's nothing else between the ends of the resistor and the power supply, then the voltage across the resistor is 24 volts, and the current through it is 2 amperes.
When the ammeter reading is zero and there are four resistor connected in seriesusing voltmeter identify which resistor causes the problem?
The ammeter is reading zero because there is no current flowing. This is because one of the resistors is faulty; the faulty resistor has an "open circuit" (open circuit means there is a broken connection). We know that: Ohms law is: V = I x R (voltage = current x resistance) Therefore because there is zero current in each resistor there will be zero voltage across each resistor. However we also know that: Kirchhoff's voltage law is: V1 +V2 +V3 + … = Vs (the sum of the voltage drops accross each component in a circuit MUST equal the supply (or battery) voltage). But if all the resistors are zero volts, then what component equals the supply (or battery) voltage? The battery voltage is developed across the open circuit… therefore the resistor which is faulty will have a voltage across it equal to the battery voltage. That easy to measure with a volt meter! hope this helps
In a simple series circuit where you have a 9V supply connected to a negative terminal with about 2 amps of current flowing you have a resistor of 100 ohms in between the 9V supply and 0V?
If a 9V supply is connected to a 100-ohm resistor, then the current is not 2 Amps,or even close to it.I = E/R = 9/100 = 0.09 amp.
A 120V power supply connected to a 30ohm resistor will produce amps of current?
V=IR, V=120 VOLTS R=30 OHMS I=V/R, I=120/30, I = 4Amps
When an inductor and resistor are connected in parallel by how many degrees is the current flow through the resistor out of phase with the current flow through the inductor?
When a resistor and an inductor are both connected to an AC supply, the current in the resistor is in phase with the voltage, while the current in the inductor is a quarter-cycle (90 degrees) behind. Supposing they both draw 1 amp on a 12-volt AC supply. The resistor will dissipate 12 watts, while the inductor will dissipate no power. Any power that enters the inductor comes back to the generator in a later part of the cycle. But the current drawn from the supply is 1.414 amps, so this would be a load with a power factor of 0.707.
A resistor has a resistance of 176 ohm How many of these resistors should be connected in parallel so that their combination draws a current of 5 amperes from a 220 volt supply line?
4 resistors were connected in parallel it yields 5A of current from 220V supply.
A 3 omega resistor is connected in parallel with a 12 omega resistor and the combination is connected to a 12-V battery How much current does the battery supply?
The 12V battery connected to the 2.4 Ohm combination will supply 12/2.4 or 5A. The individual currents will be 12/3 or 4A for the 3 Ohm resistor, and 12/12 or 1A for the 12 Ohm resistor. The 2.4 Ohm parallel combination is obtained from a simple product-over-the-sum calculation.
When a series circuit comprises of a resistor and a capacitor and is connected to an ac supply the current will what?
The equation for such circuits is given by: V=R*I +(1/C)*Integration(idt)
What happens to the applied voltage when a change in circuit resistance occurs?
When a dc supply is connected to a resistor, current flows. The current in amps is equal to the supply voltage divided by the resistance in ohms. The power used is the voltage times the current, and that appears as heat in the resistor, which might become hot to touch.
How can you measure the ampere or watt for power supply?
You can measure the current and power of a 'power supply', using an ammeter and a wattmeter. With the power supply connected to its load, the ammeter must be connected in series with the power supply's input. The wattmeter's current coil must also be connected in series with the power supply's input, and its voltage coil must be connected in parallel with the supply, taking the instrument's polarity markings into account.
When a single phase supply connect to a electric heater short circuit not there why?
The electric heater is basically a resistor, designed to have the right resistance to draw the required current. So a 2 kW heater designed for a 230 v supply is really a resistor of 28.8 ohms, so when it's connected the current is 8 amps and the power is 2 kW.
Why must an LED always have a resistor connected in series with it?
An LED usually has a resistor connected in series with it because an LED (light emitting diode) is not linear in current to voltage (like a resistor) and has to be operated within specified current and voltage conditions. In most circuits the supply voltage is higher than the forward voltage of the LED so the LED would burn up from too much current without a current limiting resistor in series. The resistor sets the voltage and current to a good operating point (voltage and current) for the LED by dropping some voltage across it. The operating point varies depending on the size, type and manufacturer of an LED so the LED's data is used to select the right resistor size for a given voltage source.
What is the current in a 12-volt circuit with two 6-ohm resistor connected in parallel?
Two 6-ohm resistors in parallel have a net effective resistance of 3 ohms.With 3 ohms connected across a 12-volt supply, the current is 12/3 = 4 amperes.
What is the function of rheostat in this experiment?
A rheostat is the name given to a variable resistor when it is used to control current. When a variable resistor is used to control voltage, we call it a potentiometer.A rheostat is connected in series with a load, and two of its three terminals are used. A potentiometer is connected in parallel with the supply, and each of its three terminals are used.So the terms 'rheostat' and 'potentiometer' are the names given to describe the function of a variable resistor, not the variable resistor itself.
